Updates en afstellen bltouch
This commit is contained in:
@@ -4,4 +4,8 @@
|
||||
#~# [main]
|
||||
#~# screen_blanking = 900
|
||||
#~# move_speed_z = 5
|
||||
#~#
|
||||
#~# [graph Printer]
|
||||
#~# heater_bed = False
|
||||
#~# extruder = False
|
||||
#~#
|
||||
|
||||
@@ -56,6 +56,19 @@ gcode:
|
||||
_KM_PRINT_STATUS ACTION=CHANGE STATUS=pop_status
|
||||
{% endif %}
|
||||
|
||||
# Met deze onderstaande codeblok wordt de printkop voor elke homing 2 mm omhoog gezet, of de printer weet wat de Z positie is of niet. https://klipper.discourse.group/t/moving-z-before-homing-or-other/1037/4
|
||||
[force_move]
|
||||
# Enable commands that force potentially unsafe movement
|
||||
enable_force_move: True
|
||||
|
||||
[gcode_macro UNSAFE_LOWER_BED]
|
||||
description: Lift Z 2mm without homing
|
||||
gcode:
|
||||
G90
|
||||
SET_KINEMATIC_POSITION Z=0
|
||||
G0 Z2 F600
|
||||
M84
|
||||
|
||||
[gcode_macro g28]
|
||||
description: Wraps the G28 command to add the Marlin "O" parameter so that
|
||||
already homed axes will not be homed again. See the Klipper documentation on
|
||||
@@ -63,5 +76,6 @@ description: Wraps the G28 command to add the Marlin "O" parameter so that
|
||||
Usage: G28 [O] ...
|
||||
rename_existing: G28.6245197
|
||||
gcode:
|
||||
UNSAFE_LOWER_BED
|
||||
{% set axes = 'XYZ'|select('in', params)|join() %}
|
||||
LAZY_HOME LAZY={('O' in params)|int}{%if axes%} AXES={axes}{%endif%}
|
||||
LAZY_HOME LAZY={('O' in params)|int}{%if axes%} AXES={axes}{%endif%}
|
||||
|
||||
@@ -5,7 +5,7 @@
|
||||
# These are examples of some likely customizations:
|
||||
# Any sheets in the below list will be available with a configurable offset.
|
||||
#variable_bed_surfaces: ['smooth_1','texture_1']
|
||||
variable_print_min: (12, 51) # example: (0, 0)
|
||||
variable_print_min: (0, 0) # example: (0, 0)
|
||||
variable_start_bed_heat_overshoot: 0.0
|
||||
variable_park_x: 5.0
|
||||
variable_park_y: 5.0
|
||||
|
||||
@@ -0,0 +1,288 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
||||
# E3 v1.2. To use this config, the firmware should be compiled for the
|
||||
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
||||
# select "Enable extra low-level configuration options" and configure
|
||||
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
||||
|
||||
# The "make flash" command does not work on the SKR mini E3. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the SKR
|
||||
# mini E3 with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# Note: This board has a design flaw in its thermistor circuits that
|
||||
# cause inaccurate temperatures (most noticeable at low temperatures).
|
||||
|
||||
# Met de DropEffect OmniDrop V2.1 is het punt links-beneden (dus het 0-punt): X = 12 en Y = 30
|
||||
# En om bij de clips vandaan te blijven wordt er aan Y nog 21 toegevoegd.
|
||||
|
||||
# Voor het verplaatsen van de X en/of Y is het nodig om Z 2.0 mm omhoog te zetten. Hierdoor komt de kop boven de clipjes en kunnen de clipjes op hun plaats blijven zitten.
|
||||
# Dit wordt geregeld in PRINT_START in start_end.cfg en in HOMING in kinematics.cfg.
|
||||
|
||||
# Invoegen van de standaard macros, geknipt uit printer.cfg
|
||||
#[include macros/standaardMacros.cfg]
|
||||
# Invoegen van macros. Deze komen uit: https://github.com/jschuh/klipper-macros
|
||||
[include macros/jschuh_macros.cfg]
|
||||
[include scherm/menu.cfg]
|
||||
[include leds/neopixel.cfg]
|
||||
|
||||
[exclude_object]
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB13
|
||||
dir_pin: !PB12
|
||||
enable_pin: !PB14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC0
|
||||
position_endstop: -14
|
||||
position_min: -14
|
||||
position_max: 195
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PB15
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB10
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PB11
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC1
|
||||
position_endstop: -51
|
||||
position_min: -51
|
||||
position_max: 160
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC6
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB0
|
||||
dir_pin: PC5
|
||||
enable_pin: !PB1
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0
|
||||
position_min: -2
|
||||
position_max: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC10
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC14
|
||||
control_pin: PA1
|
||||
#pin_up_reports_not_triggered: False
|
||||
#pin_up_touch_mode_reports_triggered: False
|
||||
x_offset: 33.7
|
||||
y_offset: -33.5
|
||||
#z_offset: 2.68
|
||||
pin_move_time: 0.680
|
||||
|
||||
[bed_screws]
|
||||
screw1: 29,31
|
||||
screw2: 196,31
|
||||
screw3: 196,206
|
||||
screw4: 29,206
|
||||
#screw5: 117,117
|
||||
|
||||
[bed_mesh]
|
||||
speed: 80
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 25,10
|
||||
mesh_max: 228.7,126.5
|
||||
probe_count: 5,5
|
||||
|
||||
[extruder]
|
||||
# DropEffect OmniaDrop V2.1
|
||||
step_pin: PB3
|
||||
dir_pin: PB4
|
||||
enable_pin: !PD2
|
||||
microsteps: 16
|
||||
gear_ratio: 5:1
|
||||
rotation_distance: 32.160
|
||||
max_extrude_cross_section: 3.0
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC8
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA0
|
||||
#control: pid
|
||||
#pid_Kp: 21.527
|
||||
#pid_Ki: 1.063
|
||||
#pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC11
|
||||
run_current: 0.500
|
||||
hold_current: 0.400
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[heater_fan my_nozzle_fan]
|
||||
# Aansturing via PT-DET pinout
|
||||
pin: PC12
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PC9
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC3
|
||||
#control: pid
|
||||
#pid_Kp: 54.027
|
||||
#pid_Ki: 0.770
|
||||
#pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA8
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[static_digital_output usb_pullup_enable]
|
||||
pins: !PC13
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: EXP1_7
|
||||
sclk_pin: EXP1_6
|
||||
sid_pin: EXP1_8
|
||||
encoder_pins: ^EXP1_5, ^EXP1_3
|
||||
click_pin: ^!EXP1_2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
[virtual_sdcard]
|
||||
path: ~/printer_data/gcodes
|
||||
on_error_gcode: CANCEL_PRINT
|
||||
|
||||
[display_status]
|
||||
|
||||
[mcu rpi]
|
||||
serial: /tmp/klipper_host_mcu
|
||||
|
||||
[adxl345]
|
||||
cs_pin: rpi:None
|
||||
|
||||
[resonance_tester]
|
||||
accel_chip: adxl345
|
||||
probe_points:
|
||||
100, 100, 20 # an example
|
||||
|
||||
### input-shaper waardes verkregen via adxl345 tuning
|
||||
[input_shaper]
|
||||
shaper_freq_x: 69.8
|
||||
shaper_type_x: mzv
|
||||
shaper_freq_y: 41.4
|
||||
shaper_type_y: ei
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 30.552
|
||||
#*# pid_ki = 2.289
|
||||
#*# pid_kd = 101.966
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 61.642
|
||||
#*# pid_ki = 0.561
|
||||
#*# pid_kd = 1694.375
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.675
|
||||
#*#
|
||||
#*# [stepper_z]
|
||||
#*#
|
||||
#*# [bed_mesh GlasbedCarbonBoven]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.250000, 0.085000, 0.025000, -0.015000, -0.027500
|
||||
#*# 0.192500, 0.072500, 0.015000, -0.015000, -0.045000
|
||||
#*# 0.052500, -0.032500, -0.037500, -0.050000, 0.015000
|
||||
#*# -0.030000, -0.017500, 0.025000, 0.072500, 0.117500
|
||||
#*# 0.032500, 0.005000, 0.042500, 0.032500, 0.127500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
#*#
|
||||
#*# [bed_mesh GlasbedCarbonBoven ]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.030000, -0.065000, -0.075000, -0.145000, -0.165000
|
||||
#*# 0.272500, 0.092500, -0.070000, -0.275000, -0.422500
|
||||
#*# 0.027500, -0.052500, -0.075000, -0.165000, -0.160000
|
||||
#*# -0.045000, -0.040000, -0.045000, -0.105000, -0.057500
|
||||
#*# 0.017500, 0.005000, 0.022500, -0.012500, 0.002500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# -0.327500, -0.370000, -0.362500, -0.365000, -0.490000
|
||||
#*# -0.285000, -0.327500, -0.385000, -0.417500, -0.482500
|
||||
#*# -0.442500, -0.385000, -0.335000, -0.302500, -0.357500
|
||||
#*# -0.460000, -0.382500, -0.365000, -0.307500, -0.282500
|
||||
#*# -0.405000, -0.302500, -0.257500, -0.222500, -0.240000
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
@@ -0,0 +1,288 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
||||
# E3 v1.2. To use this config, the firmware should be compiled for the
|
||||
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
||||
# select "Enable extra low-level configuration options" and configure
|
||||
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
||||
|
||||
# The "make flash" command does not work on the SKR mini E3. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the SKR
|
||||
# mini E3 with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# Note: This board has a design flaw in its thermistor circuits that
|
||||
# cause inaccurate temperatures (most noticeable at low temperatures).
|
||||
|
||||
# Met de DropEffect OmniDrop V2.1 is het punt links-beneden (dus het 0-punt): X = 12 en Y = 30
|
||||
# En om bij de clips vandaan te blijven wordt er aan Y nog 21 toegevoegd.
|
||||
|
||||
# Voor het verplaatsen van de X en/of Y is het nodig om Z 2.0 mm omhoog te zetten. Hierdoor komt de kop boven de clipjes en kunnen de clipjes op hun plaats blijven zitten.
|
||||
# Dit wordt geregeld in PRINT_START in start_end.cfg en in HOMING in kinematics.cfg.
|
||||
|
||||
# Invoegen van de standaard macros, geknipt uit printer.cfg
|
||||
#[include macros/standaardMacros.cfg]
|
||||
# Invoegen van macros. Deze komen uit: https://github.com/jschuh/klipper-macros
|
||||
[include macros/jschuh_macros.cfg]
|
||||
[include scherm/menu.cfg]
|
||||
[include leds/neopixel.cfg]
|
||||
|
||||
[exclude_object]
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB13
|
||||
dir_pin: !PB12
|
||||
enable_pin: !PB14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC0
|
||||
position_endstop: -14
|
||||
position_min: -14
|
||||
position_max: 195
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PB15
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB10
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PB11
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC1
|
||||
position_endstop: -51
|
||||
position_min: -51
|
||||
position_max: 160
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC6
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB0
|
||||
dir_pin: PC5
|
||||
enable_pin: !PB1
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0
|
||||
position_min: -2
|
||||
position_max: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC10
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC14
|
||||
control_pin: PA1
|
||||
#pin_up_reports_not_triggered: False
|
||||
#pin_up_touch_mode_reports_triggered: False
|
||||
x_offset: 33.7
|
||||
y_offset: -33.5
|
||||
#z_offset: 2.68
|
||||
pin_move_time: 0.680
|
||||
|
||||
[bed_screws]
|
||||
screw1: 29,31
|
||||
screw2: 196,31
|
||||
screw3: 196,206
|
||||
screw4: 29,206
|
||||
#screw5: 117,117
|
||||
|
||||
[bed_mesh]
|
||||
speed: 80
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 25,10
|
||||
mesh_max: 228.7,126.5
|
||||
probe_count: 5,5
|
||||
|
||||
[extruder]
|
||||
# DropEffect OmniaDrop V2.1
|
||||
step_pin: PB3
|
||||
dir_pin: PB4
|
||||
enable_pin: !PD2
|
||||
microsteps: 16
|
||||
gear_ratio: 5:1
|
||||
rotation_distance: 32.160
|
||||
max_extrude_cross_section: 3.0
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC8
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA0
|
||||
#control: pid
|
||||
#pid_Kp: 21.527
|
||||
#pid_Ki: 1.063
|
||||
#pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC11
|
||||
run_current: 0.500
|
||||
hold_current: 0.400
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[heater_fan my_nozzle_fan]
|
||||
# Aansturing via PT-DET pinout
|
||||
pin: PC12
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PC9
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC3
|
||||
#control: pid
|
||||
#pid_Kp: 54.027
|
||||
#pid_Ki: 0.770
|
||||
#pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA8
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[static_digital_output usb_pullup_enable]
|
||||
pins: !PC13
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: EXP1_7
|
||||
sclk_pin: EXP1_6
|
||||
sid_pin: EXP1_8
|
||||
encoder_pins: ^EXP1_5, ^EXP1_3
|
||||
click_pin: ^!EXP1_2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
[virtual_sdcard]
|
||||
path: ~/printer_data/gcodes
|
||||
on_error_gcode: CANCEL_PRINT
|
||||
|
||||
[display_status]
|
||||
|
||||
[mcu rpi]
|
||||
serial: /tmp/klipper_host_mcu
|
||||
|
||||
[adxl345]
|
||||
cs_pin: rpi:None
|
||||
|
||||
[resonance_tester]
|
||||
accel_chip: adxl345
|
||||
probe_points:
|
||||
100, 100, 20 # an example
|
||||
|
||||
### input-shaper waardes verkregen via adxl345 tuning
|
||||
[input_shaper]
|
||||
shaper_freq_x: 69.8
|
||||
shaper_type_x: mzv
|
||||
shaper_freq_y: 41.4
|
||||
shaper_type_y: ei
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 31.285
|
||||
#*# pid_ki = 2.343
|
||||
#*# pid_kd = 104.414
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 61.642
|
||||
#*# pid_ki = 0.561
|
||||
#*# pid_kd = 1694.375
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.675
|
||||
#*#
|
||||
#*# [stepper_z]
|
||||
#*#
|
||||
#*# [bed_mesh GlasbedCarbonBoven]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.250000, 0.085000, 0.025000, -0.015000, -0.027500
|
||||
#*# 0.192500, 0.072500, 0.015000, -0.015000, -0.045000
|
||||
#*# 0.052500, -0.032500, -0.037500, -0.050000, 0.015000
|
||||
#*# -0.030000, -0.017500, 0.025000, 0.072500, 0.117500
|
||||
#*# 0.032500, 0.005000, 0.042500, 0.032500, 0.127500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
#*#
|
||||
#*# [bed_mesh GlasbedCarbonBoven ]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.030000, -0.065000, -0.075000, -0.145000, -0.165000
|
||||
#*# 0.272500, 0.092500, -0.070000, -0.275000, -0.422500
|
||||
#*# 0.027500, -0.052500, -0.075000, -0.165000, -0.160000
|
||||
#*# -0.045000, -0.040000, -0.045000, -0.105000, -0.057500
|
||||
#*# 0.017500, 0.005000, 0.022500, -0.012500, 0.002500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# -0.327500, -0.370000, -0.362500, -0.365000, -0.490000
|
||||
#*# -0.285000, -0.327500, -0.385000, -0.417500, -0.482500
|
||||
#*# -0.442500, -0.385000, -0.335000, -0.302500, -0.357500
|
||||
#*# -0.460000, -0.382500, -0.365000, -0.307500, -0.282500
|
||||
#*# -0.405000, -0.302500, -0.257500, -0.222500, -0.240000
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
@@ -0,0 +1,288 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
||||
# E3 v1.2. To use this config, the firmware should be compiled for the
|
||||
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
||||
# select "Enable extra low-level configuration options" and configure
|
||||
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
||||
|
||||
# The "make flash" command does not work on the SKR mini E3. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the SKR
|
||||
# mini E3 with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# Note: This board has a design flaw in its thermistor circuits that
|
||||
# cause inaccurate temperatures (most noticeable at low temperatures).
|
||||
|
||||
# Met de DropEffect OmniDrop V2.1 is het punt links-beneden (dus het 0-punt): X = 12 en Y = 30
|
||||
# En om bij de clips vandaan te blijven wordt er aan Y nog 21 toegevoegd.
|
||||
|
||||
# Voor het verplaatsen van de X en/of Y is het nodig om Z 2.0 mm omhoog te zetten. Hierdoor komt de kop boven de clipjes en kunnen de clipjes op hun plaats blijven zitten.
|
||||
# Dit wordt geregeld in PRINT_START in start_end.cfg en in HOMING in kinematics.cfg.
|
||||
|
||||
# Invoegen van de standaard macros, geknipt uit printer.cfg
|
||||
#[include macros/standaardMacros.cfg]
|
||||
# Invoegen van macros. Deze komen uit: https://github.com/jschuh/klipper-macros
|
||||
[include macros/jschuh_macros.cfg]
|
||||
[include scherm/menu.cfg]
|
||||
[include leds/neopixel.cfg]
|
||||
|
||||
[exclude_object]
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB13
|
||||
dir_pin: !PB12
|
||||
enable_pin: !PB14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC0
|
||||
position_endstop: -14
|
||||
position_min: -14
|
||||
position_max: 195
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PB15
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB10
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PB11
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC1
|
||||
position_endstop: -51
|
||||
position_min: -51
|
||||
position_max: 160
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC6
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB0
|
||||
dir_pin: PC5
|
||||
enable_pin: !PB1
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0
|
||||
position_min: -2
|
||||
position_max: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC10
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC14
|
||||
control_pin: PA1
|
||||
#pin_up_reports_not_triggered: False
|
||||
#pin_up_touch_mode_reports_triggered: False
|
||||
x_offset: 32.3
|
||||
y_offset: -33.5
|
||||
#z_offset: 2.68
|
||||
pin_move_time: 0.680
|
||||
|
||||
[bed_screws]
|
||||
screw1: 29,31
|
||||
screw2: 196,31
|
||||
screw3: 196,206
|
||||
screw4: 29,206
|
||||
#screw5: 117,117
|
||||
|
||||
[bed_mesh]
|
||||
speed: 80
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 25,10
|
||||
mesh_max: 228.7,126.5
|
||||
probe_count: 5,5
|
||||
|
||||
[extruder]
|
||||
# DropEffect OmniaDrop V2.1
|
||||
step_pin: PB3
|
||||
dir_pin: PB4
|
||||
enable_pin: !PD2
|
||||
microsteps: 16
|
||||
gear_ratio: 5:1
|
||||
rotation_distance: 32.160
|
||||
max_extrude_cross_section: 3.0
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC8
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA0
|
||||
#control: pid
|
||||
#pid_Kp: 21.527
|
||||
#pid_Ki: 1.063
|
||||
#pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC11
|
||||
run_current: 0.500
|
||||
hold_current: 0.400
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[heater_fan my_nozzle_fan]
|
||||
# Aansturing via PT-DET pinout
|
||||
pin: PC12
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PC9
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC3
|
||||
#control: pid
|
||||
#pid_Kp: 54.027
|
||||
#pid_Ki: 0.770
|
||||
#pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA8
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[static_digital_output usb_pullup_enable]
|
||||
pins: !PC13
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: EXP1_7
|
||||
sclk_pin: EXP1_6
|
||||
sid_pin: EXP1_8
|
||||
encoder_pins: ^EXP1_5, ^EXP1_3
|
||||
click_pin: ^!EXP1_2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
[virtual_sdcard]
|
||||
path: ~/printer_data/gcodes
|
||||
on_error_gcode: CANCEL_PRINT
|
||||
|
||||
[display_status]
|
||||
|
||||
[mcu rpi]
|
||||
serial: /tmp/klipper_host_mcu
|
||||
|
||||
[adxl345]
|
||||
cs_pin: rpi:None
|
||||
|
||||
[resonance_tester]
|
||||
accel_chip: adxl345
|
||||
probe_points:
|
||||
100, 100, 20 # an example
|
||||
|
||||
### input-shaper waardes verkregen via adxl345 tuning
|
||||
[input_shaper]
|
||||
shaper_freq_x: 69.8
|
||||
shaper_type_x: mzv
|
||||
shaper_freq_y: 41.4
|
||||
shaper_type_y: ei
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 31.285
|
||||
#*# pid_ki = 2.343
|
||||
#*# pid_kd = 104.414
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 63.394
|
||||
#*# pid_ki = 0.394
|
||||
#*# pid_kd = 2550.799
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.675
|
||||
#*#
|
||||
#*# [stepper_z]
|
||||
#*#
|
||||
#*# [bed_mesh GlasbedCarbonBoven]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.250000, 0.085000, 0.025000, -0.015000, -0.027500
|
||||
#*# 0.192500, 0.072500, 0.015000, -0.015000, -0.045000
|
||||
#*# 0.052500, -0.032500, -0.037500, -0.050000, 0.015000
|
||||
#*# -0.030000, -0.017500, 0.025000, 0.072500, 0.117500
|
||||
#*# 0.032500, 0.005000, 0.042500, 0.032500, 0.127500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
#*#
|
||||
#*# [bed_mesh GlasbedCarbonBoven ]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.030000, -0.065000, -0.075000, -0.145000, -0.165000
|
||||
#*# 0.272500, 0.092500, -0.070000, -0.275000, -0.422500
|
||||
#*# 0.027500, -0.052500, -0.075000, -0.165000, -0.160000
|
||||
#*# -0.045000, -0.040000, -0.045000, -0.105000, -0.057500
|
||||
#*# 0.017500, 0.005000, 0.022500, -0.012500, 0.002500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# -0.327500, -0.370000, -0.362500, -0.365000, -0.490000
|
||||
#*# -0.285000, -0.327500, -0.385000, -0.417500, -0.482500
|
||||
#*# -0.442500, -0.385000, -0.335000, -0.302500, -0.357500
|
||||
#*# -0.460000, -0.382500, -0.365000, -0.307500, -0.282500
|
||||
#*# -0.405000, -0.302500, -0.257500, -0.222500, -0.240000
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 25.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
@@ -36,9 +36,9 @@ enable_pin: !PB14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC0
|
||||
position_endstop: -13.5
|
||||
position_min: -13.5
|
||||
position_max: 221.5
|
||||
position_endstop: -14
|
||||
position_min: -14
|
||||
position_max: 195
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
@@ -56,7 +56,7 @@ rotation_distance: 40
|
||||
endstop_pin: ^PC1
|
||||
position_endstop: -51
|
||||
position_min: -51
|
||||
position_max: 185
|
||||
position_max: 160
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
@@ -87,7 +87,7 @@ sensor_pin: ^PC14
|
||||
control_pin: PA1
|
||||
#pin_up_reports_not_triggered: False
|
||||
#pin_up_touch_mode_reports_triggered: False
|
||||
x_offset: 33.7
|
||||
x_offset: 32.3
|
||||
y_offset: -33.5
|
||||
#z_offset: 2.68
|
||||
pin_move_time: 0.680
|
||||
@@ -103,7 +103,7 @@ screw4: 29,206
|
||||
speed: 80
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 25,10
|
||||
mesh_max: 200,150
|
||||
mesh_max: 228.7,126.5
|
||||
probe_count: 5,5
|
||||
|
||||
[extruder]
|
||||
@@ -215,18 +215,18 @@ shaper_type_y: ei
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 30.552
|
||||
#*# pid_ki = 2.289
|
||||
#*# pid_kd = 101.966
|
||||
#*# pid_kp = 31.285
|
||||
#*# pid_ki = 2.343
|
||||
#*# pid_kd = 104.414
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 61.642
|
||||
#*# pid_ki = 0.561
|
||||
#*# pid_kd = 1694.375
|
||||
#*# pid_kp = 63.394
|
||||
#*# pid_ki = 0.394
|
||||
#*# pid_kd = 2550.799
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.675
|
||||
#*# z_offset = 2.935
|
||||
#*#
|
||||
#*# [stepper_z]
|
||||
#*#
|
||||
|
||||
Reference in New Issue
Block a user