Kevin O'Connor 98f2adbcb5 extruder: Rework maximum retraction check ...

On a retract move (which are common during "wipe" operations), treat
the move as if it were an extrude only move.  It's valid for a retract
move to reverse more filament then it would be practical to push.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2017-05-02 08:57:38 -04:00

..

cartesian.py

klippy: Support minimum/maximum value checks on configuration variables

2017-04-11 11:42:55 -04:00

chelper.py

hub-ctrl: Add support for micro-controller reset via RPi usb power toggling

2017-04-13 13:20:13 -04:00

console.py

msgproto: Rework dump() so it also works with params

2017-04-25 13:58:13 -04:00

corexy.py

klippy: Support minimum/maximum value checks on configuration variables

2017-04-11 11:42:55 -04:00

delta.py

klippy: Support minimum/maximum value checks on configuration variables

2017-04-11 11:42:55 -04:00

extruder.py

extruder: Rework maximum retraction check

2017-05-02 08:57:38 -04:00

fan.py

klippy: Support minimum/maximum value checks on configuration variables

2017-04-11 11:42:55 -04:00

gcode.py

gcode: Check for invalid speeds

2017-05-02 07:54:48 -04:00

heater.py

klippy: Support minimum/maximum value checks on configuration variables

2017-04-11 11:42:55 -04:00

homing.py

gcode: Rework homing to use greenlets

2016-12-09 17:09:51 -05:00

klippy.py

queuelogger: Add critical information to each logfile on rollover

2017-05-01 14:48:44 -04:00

list.h

Initial commit of source code.

2016-05-25 11:37:40 -04:00

mcu.py

queuelogger: Add critical information to each logfile on rollover

2017-05-01 14:48:44 -04:00

msgproto.py

msgproto: Wrap strings passed via output() in repr()

2017-05-02 07:54:48 -04:00

parsedump.py

Initial commit of source code.

2016-05-25 11:37:40 -04:00

pins.py

mcu: Support config mechanism for translating seconds to clock ticks

2017-03-13 00:38:17 -04:00

pyhelper.c

reactor: Use the system monotonic clock instead of the normal system clock

2017-02-06 13:31:34 -05:00

pyhelper.h

stepcompress: Modify check_expand() into check_push()

2017-04-07 19:05:04 -04:00

queuelogger.py

queuelogger: Add critical information to each logfile on rollover

2017-05-01 14:48:44 -04:00

reactor.py

reactor: Fix bug causing end() to not always work

2017-04-13 13:20:13 -04:00

serialhdl.py

reactor: Support pause() command even when the reactor is not running

2017-04-01 12:26:24 -04:00

serialqueue.c

serialqueue: Message receive_time must be taken after read()

2017-03-24 19:16:33 -04:00

serialqueue.h

serialqueue: Remove serialqueue_flush_ready()

2016-12-30 20:15:05 -05:00

stepcompress.c

stepcompress: Simplify delta Z only move calculations

2017-04-20 00:56:18 -04:00

stepper.py

klippy: Support minimum/maximum value checks on configuration variables

2017-04-11 11:42:55 -04:00

toolhead.py

klippy: Don't log stats when the printer is idle

2017-04-14 10:38:37 -04:00

util.py

klippy: Log the type of cpu the host is running on

2017-02-12 19:14:26 -05:00