Kevin O'Connor 9466c2d66c stm32f1: Add support for entering the bootloader via USB ...

Add support for entering the "stm32duino" bootloader via the arduino
1200 baud USB request.  Add supprot for flashing over USB via the
"make flash" command.

Rename the existing "make flash" command to "make serialflash".

Default to using a bootloader in Kconfig.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2019-03-08 22:22:41 -05:00

..

atsam

atsam: Improve support for flashing over USB

2019-03-08 22:22:41 -05:00

atsamd

atsamd: Add support to "make flash" to automatically enter the bootloader

2019-03-08 22:22:41 -05:00

avr

Makefile: Reduce use of $^ in build rules

2019-03-02 12:01:44 -05:00

generic

armcm_timer: Add a generic timer mechanism for ARM CortexM3/M4 chips

2019-02-06 22:03:09 -05:00

linux

linux: Add support for bi-directional SPI communication

2018-07-24 11:16:05 -04:00

lpc176x

lpc176x: Add support for flashing via "make flash"

2019-03-08 22:22:41 -05:00

pru

Makefile: Reduce use of $^ in build rules

2019-03-02 12:01:44 -05:00

simulator

simulator: Wrap code to 80 columns

2019-02-27 14:20:15 -05:00

stm32f1

stm32f1: Add support for entering the bootloader via USB

2019-03-08 22:22:41 -05:00

adccmds.c

adccmds: Run gpio_adc_setup() before oid_alloc()

2019-01-13 11:03:30 -05:00

basecmd.c

basecmd: Rename get_status to get_clock

2018-05-29 10:57:29 -04:00

basecmd.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

buttons.c

buttons: Wrap code to 80 columns

2019-02-27 14:20:15 -05:00

byteorder.h

byteorder: Add a header file defining common byteswap functions

2018-05-21 09:44:40 -04:00

command.c

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

command.h

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

compiler.h

compiler.h: Check if __aligned and __section macros are already defined

2016-06-13 23:18:59 -04:00

ctr.h

build: Avoid linker magic in compile_time_request.c unique id generation

2017-05-26 12:32:02 -04:00

debugcmds.c

debugcmds: Add support for reading/writing 32bit values

2019-02-07 11:50:14 -05:00

endstop.c

endstop: Eliminate end_stop_set_oversample command

2017-10-12 11:59:27 -04:00

gpiocmds.c

gpiocmds: Add update_digital_out command

2018-06-27 12:10:39 -04:00

i2ccmds.c

i2ccmds: Pass the i2c address as a 7-bit number (0-127)

2019-01-07 20:00:44 -05:00

Kconfig

atsamd: Initial support for SAMD51

2019-01-28 20:02:16 -05:00

lcd_hd44780.c

lcd_hd44780: Add micro-controller code for the HD44780 LCD chip

2018-03-06 11:30:34 -05:00

lcd_st7920.c

lcd_st7920: Use a longer delay at the start of each command/data

2018-06-22 23:47:09 -04:00

Makefile

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

pwmcmds.c

pwmcmds: Wrap code to 80 columns

2019-02-27 14:20:15 -05:00

sched.c

sched: Force sched_try_shutdown to be inlined

2018-10-13 11:47:00 -04:00

sched.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

spi_software.c

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spi_software.h

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spicmds.c

spicmds: Wrap code to 80 columns

2019-02-27 14:20:15 -05:00

spicmds.h

thermocouple: Add initial support for common SPI temperature sensing chips

2018-07-24 11:16:05 -04:00

stepper.c

stepper: Wrap code to 80 columns

2019-02-27 14:20:15 -05:00

stepper.h

stepper: Introduce stepper_get_position command and remove from endstop.c

2017-03-09 14:54:52 -05:00

thermocouple.c

thermocouple: Minor fixes

2018-07-25 09:06:50 -04:00

tmcuart.c

pins: Add support for pull down resistors

2019-02-27 11:13:21 -05:00