h3n3/klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
Files
02ee379f82445016fd1b18b79b492f9a0f13725e
klipper/src
History
Lucio Tarantino dac42efbd9 htu21d: Support for HTI21D family sensor on I2C bus (#2803) 
Signed-off-by: Lucio Tarantino <lucio.tarantino@gmail.com>
2020-05-03 18:47:24 -04:00
..
atsam
atsam: Fix typo causing chipid to not be fully read
2019-11-27 14:33:20 -05:00
atsamd
atsamd: Enable chipid as usb serial number
2019-11-25 19:30:31 -05:00
avr
avr: implement i2c_read
2020-01-13 22:29:50 -05:00
generic
armcm_boot: Additional code for broken bootloaders
2020-03-04 19:50:56 -05:00
linux
htu21d: Support for HTI21D family sensor on I2C bus (#2803)
2020-05-03 18:47:24 -04:00
lpc176x
lpc176x: Add support for additional i2c buses
2020-04-21 16:11:39 -04:00
pru
pru: The TMR_CNT is cleared by writing all ones
2019-03-31 13:48:50 -04:00
simulator
simulator: Wrap code to 80 columns
2019-02-27 14:20:15 -05:00
stm32
stm32: Wait for setup complete to enable ep0 rx in usbotg.c
2020-05-03 12:00:47 -04:00
adccmds.c
adccmds: Run gpio_adc_setup() before oid_alloc()
2019-01-13 11:03:30 -05:00
basecmd.c
basecmd: No need for finalize_config command to send "config" response
2020-02-20 12:01:21 -05:00
basecmd.h
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
buttons.c
buttons: initialize mcu buttons based on inverted state
2019-07-05 20:01:07 -04:00
byteorder.h
byteorder: Add a header file defining common byteswap functions
2018-05-21 09:44:40 -04:00
command.c
command: Wait to send ack until after processing commands
2018-05-28 10:43:40 -04:00
command.h
buildcommands: Match DECL_X names to the actual C macro names
2019-08-22 13:26:30 -04:00
compiler.h
compiler.h: Check if __aligned and __section macros are already defined
2016-06-13 23:18:59 -04:00
ctr.h
ctr: Encode negative integers in normal hex notation
2019-08-22 13:06:44 -04:00
debugcmds.c
debugcmds: Add support for reading/writing 32bit values
2019-02-07 11:50:14 -05:00
endstop.c
endstop: Rename mcu end_stop commands to endstop
2019-07-12 08:10:53 -04:00
gpiocmds.c
gpiocmds: Specify soft pwm duration in clock ticks
2019-05-26 11:09:32 -04:00
i2ccmds.c
avr: implement i2c_read
2020-01-13 22:29:50 -05:00
initial_pins.c
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
initial_pins.h
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
Kconfig
stm32f0: Remove hal based stm32f0 implementation
2020-01-14 17:08:01 -05:00
lcd_hd44780.c
lcd_hd44780: Minor change to timing delays
2019-11-26 09:49:43 -05:00
lcd_st7920.c
lcd_st7920: Add brief delay around gpio toggle calls on fast MCUs
2019-08-10 11:45:15 -04:00
Makefile
initial_pins: Only build when CONFIG_HAVE_GPIO is enabled
2019-07-24 01:09:45 -04:00
neopixel.c
neopixel: Make sure there is a minimum low duration after a long pulse
2020-04-21 13:12:56 -04:00
pwmcmds.c
pwmcmds: allow 16-bit resolution
2019-04-05 19:02:48 -04:00
sched.c
sched: Force sched_try_shutdown to be inlined
2018-10-13 11:47:00 -04:00
sched.h
pru: Support config_reset command to manually reset mcu
2017-09-03 23:16:38 -04:00
spi_software.c
spi_software: Remove unused include file
2019-08-17 13:49:03 -04:00
spi_software.h
spi_software: Implementation of software spi
2019-02-13 11:52:20 -05:00
spicmds.c
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
spicmds.h
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
stepper.c
stepper: Add some comments on s->position tracking
2020-03-04 14:30:41 -05:00
stepper.h
stepper: Introduce stepper_get_position command and remove from endstop.c
2017-03-09 14:54:52 -05:00
thermocouple.c
thermocouple: Define thermocouple types using enumerations
2019-03-17 19:38:18 -04:00
tmcuart.c
tmcuart: Fix typo in function name
2019-09-01 14:56:09 -04:00