config: Add BigTreeTech EBB V1.2 / EBB SB V1.0 / E3EZ / M5P / M8P V1.1 / Octopus Max EZ
Signed-off-by: Alan.Ma from BigTreeTech tech@biqu3d.com Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
bigtreetech
committed by
Kevin O'Connor
Kevin O'Connor
parent
1979c9d090
commit
f250bdfd8a
332
config/generic-bigtreetech-octopus-max-ez.cfg
Normal file
332
config/generic-bigtreetech-octopus-max-ez.cfg
Normal file
@@ -0,0 +1,332 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH Octopus Max EZ.
|
||||
# To use this config, the firmware should be compiled for the
|
||||
# STM32H723 with a "128KiB bootloader" "25 MHz crystal"
|
||||
# and "USB (on PA11/PA12)" or "CAN bus (on PD0/PD1)".
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# Motor-1
|
||||
[stepper_x]
|
||||
step_pin: PC13
|
||||
dir_pin: PC14
|
||||
enable_pin: !PE6
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: PF0
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
# Motor-2
|
||||
[stepper_y]
|
||||
step_pin: PE4
|
||||
dir_pin: PE5
|
||||
enable_pin: !PE3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: PF2
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
# Motor-3
|
||||
[stepper_z]
|
||||
step_pin: PE1
|
||||
dir_pin: PE0
|
||||
enable_pin: !PE2
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: PF4
|
||||
position_endstop: 0.5
|
||||
position_max: 200
|
||||
|
||||
# Motor-4
|
||||
# The Octopus only has 4 heater outputs which leaves an extra stepper
|
||||
# This can be used for a second Z stepper, dual_carriage, extruder co-stepper,
|
||||
# or other accesory such as an MMU
|
||||
#[stepper_]
|
||||
#step_pin: PB8
|
||||
#dir_pin: PB9
|
||||
#enable_pin: PB7
|
||||
#endstop_pin: PF3
|
||||
#...
|
||||
|
||||
# Motor-5
|
||||
[extruder]
|
||||
step_pin: PB5
|
||||
dir_pin: PB4
|
||||
enable_pin: !PB6
|
||||
microsteps: 16
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PF6 # HE0
|
||||
sensor_pin: PB0 # T0
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
#[filament_switch_sensor material_0]
|
||||
#switch_pin: PF1
|
||||
|
||||
# Motor-6
|
||||
#[extruder1]
|
||||
#step_pin: PG15
|
||||
#dir_pin: PB3
|
||||
#enable_pin: !PD5
|
||||
#heater_pin: PA0 # HE1
|
||||
#sensor_pin: PC5 # T1
|
||||
#...
|
||||
|
||||
#[filament_switch_sensor material_1]
|
||||
#switch_pin: PC15
|
||||
|
||||
# Motor-7
|
||||
#[extruder2]
|
||||
#step_pin: PD3
|
||||
#dir_pin: PD2
|
||||
#enable_pin: !PD4
|
||||
#heater_pin: PF9 # HE2
|
||||
#sensor_pin: PC4 # T2
|
||||
#...
|
||||
|
||||
# Motor-8
|
||||
#[extruder3]
|
||||
#step_pin: PA10
|
||||
#dir_pin: PA9
|
||||
#enable_pin: !PA15
|
||||
#heater_pin: PF7 # HE3
|
||||
#sensor_pin: PA7 # T3
|
||||
#...
|
||||
|
||||
# Motor-9
|
||||
#[extruder4]
|
||||
#step_pin: PA8
|
||||
#dir_pin: PC7
|
||||
#enable_pin: !PC9
|
||||
#...
|
||||
|
||||
# Motor-10
|
||||
#[extruder5]
|
||||
#step_pin: PG6
|
||||
#dir_pin: PC6
|
||||
#enable_pin: !PC8
|
||||
#...
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PF5
|
||||
sensor_pin: PB1 # TB
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA6
|
||||
|
||||
#[heater_fan fan1]
|
||||
#pin: PA5
|
||||
|
||||
#[heater_fan fan2]
|
||||
#pin: PA4
|
||||
|
||||
#[heater_fan fan3]
|
||||
#pin: PA3
|
||||
|
||||
#[heater_fan fan4]
|
||||
#pin: PA1
|
||||
#tachometer_pin: PC3
|
||||
|
||||
#[heater_fan fan5]
|
||||
#pin: PF8
|
||||
#tachometer_pin: PC1
|
||||
|
||||
#[heater_fan fan6]
|
||||
#pin: PA2
|
||||
#tachometer_pin: PC2
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
########################################
|
||||
# TMC2209 configuration
|
||||
########################################
|
||||
|
||||
#[tmc2209 stepper_x]
|
||||
#uart_pin: PG14
|
||||
##diag_pin: PF0
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 stepper_y]
|
||||
#uart_pin: PG13
|
||||
##diag_pin: PF2
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 stepper_z]
|
||||
#uart_pin: PG12
|
||||
##diag_pin: PF4
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 stepper_]
|
||||
#uart_pin: PG11
|
||||
##diag_pin: PF3
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder]
|
||||
#uart_pin: PG10
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder1]
|
||||
#uart_pin: PG9
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder2]
|
||||
#uart_pin: PD7
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder3]
|
||||
#uart_pin: PD6
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder4]
|
||||
#uart_pin: PG8
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder5]
|
||||
#uart_pin: PG7
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
########################################
|
||||
# TMC2130 configuration
|
||||
########################################
|
||||
|
||||
#[tmc2130 stepper_x]
|
||||
#cs_pin: PG14
|
||||
#spi_bus: spi4
|
||||
##diag1_pin: PF0
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 stepper_y]
|
||||
#cs_pin: PG13
|
||||
#spi_bus: spi4
|
||||
##diag1_pin: PF2
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 stepper_z]
|
||||
#cs_pin: PG12
|
||||
#spi_bus: spi4
|
||||
##diag1_pin: PF4
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 stepper_]
|
||||
#cs_pin: PG11
|
||||
#spi_bus: spi4
|
||||
##diag1_pin: PF3
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder]
|
||||
#cs_pin: PG10
|
||||
#spi_bus: spi4
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder1]
|
||||
#cs_pin: PG9
|
||||
#spi_bus: spi4
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder2]
|
||||
#cs_pin: PD7
|
||||
#spi_bus: spi4
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder3]
|
||||
#cs_pin: PD6
|
||||
#spi_bus: spi4
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder4]
|
||||
#cs_pin: PG8
|
||||
#spi_bus: spi4
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder5]
|
||||
#cs_pin: PG7
|
||||
#spi_bus: spi4
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# FPC header, Aliases EXP1 & EXP2 for mini12864
|
||||
EXP1_1=PG2, EXP1_2=PD15,
|
||||
EXP1_3=PD14, EXP1_4=PD13,
|
||||
EXP1_5=PD12, EXP1_6=PD11,
|
||||
EXP1_7=PD10, EXP1_8=PE15,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
|
||||
# EXP2 header
|
||||
EXP2_1=PE13, EXP2_2=PE12,
|
||||
EXP2_3=PG5, EXP2_4=PE11,
|
||||
EXP2_5=PG4, EXP2_6=PE14,
|
||||
EXP2_7=PG3, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=<NC>
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
#[bltouch]
|
||||
#sensor_pin: PB14
|
||||
#control_pin: PB15
|
||||
|
||||
# Proximity switch
|
||||
#[probe]
|
||||
#pin: PF11
|
||||
|
||||
#[output_pin ps_on_pin]
|
||||
#pin: PF13
|
||||
|
||||
#[output_pin pf12_pin]
|
||||
#pin: PF12
|
||||
|
||||
#[neopixel my_neopixel_1]
|
||||
#pin: PE10
|
||||
|
||||
#[neopixel my_neopixel_2]
|
||||
#pin: PE9
|
||||
|
||||
#[hall_filament_width_sensor]
|
||||
#adc1: PC0
|
||||
#adc2: PF10
|
||||
|
||||
#[adxl345]
|
||||
#cs_pin: PF14
|
||||
#spi_bus: spi4
|
||||
Reference in New Issue
Block a user