config: Don't use arduino mega aliases in example config files

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

config/kit-voron2-250mm.cfg

@@ -30,14 +30,12 @@
 # Mcu for X/Y/E steppers
 serial: /dev/serial/by-id/**INSERT_YOUR_ARDUINO_DEFINITION_HERE**
 #   Obtain definition by "ls -l /dev/serial/by-id/"
-pin_map: arduino
 restart_method: arduino
 
 [mcu z]
 # Mcu for Z steppers
 serial: /dev/serial/by-id/**INSERT_YOUR_ARDUINO_DEFINITION_HERE**
 #   Obtain definition by "ls -l /dev/serial/by-id/"
-pin_map: arduino
 restart_method: arduino
 
 [printer]
@@ -49,14 +47,14 @@ max_z_accel: 350
 
 [stepper_x]
 # B Stepper
-step_pin: ar54
-dir_pin: !ar55
-enable_pin: !ar38
+step_pin: PF0
+dir_pin: !PF1
+enable_pin: !PD7
 #   X on mcu_xye
 microsteps: 16
 rotation_distance: 40
 #   80 steps per mm - 1.8 deg - 1/16 microstepping
-endstop_pin: ^ar2
+endstop_pin: ^PE4
 #   X_MAX on mcu_xye
 position_min: 0
 position_endstop: 250
@@ -66,14 +64,14 @@ homing_retract_dist: 5
 
 [stepper_y]
 # A Stepper
-step_pin: ar60
-dir_pin: !ar61
-enable_pin: !ar56
+step_pin: PF6
+dir_pin: !PF7
+enable_pin: !PF2
 #   Y on mcu_xye
 microsteps: 16
 rotation_distance: 40
 #   80 steps per mm - 1.8 deg - 1/16 microstepping
-endstop_pin: ^ar15
+endstop_pin: ^PJ0
 #   Y_MAX on mcu_xye
 position_min: 0
 position_endstop: 250
@@ -83,14 +81,14 @@ homing_retract_dist: 5
 
 [stepper_z]
 # Z0 Stepper - Front Left
-step_pin: z:ar54
-dir_pin: !z:ar55
-enable_pin: !z:ar38
+step_pin: z:PF0
+dir_pin: !z:PF1
+enable_pin: !z:PD7
 #   X on mcu_z
 microsteps: 16
 rotation_distance: 8
 #   400 steps per mm - 1.8 deg - 1/16 microstepping
-endstop_pin: ^!z:ar18
+endstop_pin: ^!z:PD3
 #   Z_MIN on mcu_z
 position_endstop: -0.2
 #   Offset (in mm) for nozzle to bed off z switch
@@ -103,9 +101,9 @@ homing_retract_dist: 3.0
 
 [stepper_z1]
 # Z1 Stepper - Rear Left
-step_pin: z:ar60
-dir_pin: z:ar61
-enable_pin: !z:ar56
+step_pin: z:PF6
+dir_pin: z:PF7
+enable_pin: !z:PF2
 #   Y on mcu_z
 microsteps: 16
 rotation_distance: 8
@@ -113,9 +111,9 @@ rotation_distance: 8
 
 [stepper_z2]
 # Z2 Stepper - Rear Right
-step_pin: z:ar46
-dir_pin: !z:ar48
-enable_pin: !z:ar62
+step_pin: z:PL3
+dir_pin: !z:PL1
+enable_pin: !z:PK0
 #   Z on mcu_z
 microsteps: 16
 rotation_distance: 8
@@ -123,18 +121,18 @@ rotation_distance: 8
 
 [stepper_z3]
 # Z3 Stepper - Front Right
-step_pin: z:ar26
-dir_pin: z:ar28
-enable_pin: !z:ar24
+step_pin: z:PA4
+dir_pin: z:PA6
+enable_pin: !z:PA2
 #   E0 on mcu_z
 microsteps: 16
 rotation_distance: 8
 #   400 steps per mm - 1.8 deg - 1/16 microstepping
 
 [extruder]
-step_pin: ar26
-dir_pin: ar28
-enable_pin: !ar24
+step_pin: PA4
+dir_pin: PA6
+enable_pin: !PA2
 #   E0 on mcu_xye
 microsteps: 16
 rotation_distance: 5.76576
@@ -143,11 +141,11 @@ nozzle_diameter: 0.400
 filament_diameter: 1.750
 max_extrude_only_distance: 780.0
 #   This is set high to allow the load/unload filament macros to run
-heater_pin: ar10
+heater_pin: PB4
 #   D10 on mcu_xye
 max_power: 1.0
 sensor_type: NTC 100K beta 3950
-sensor_pin: analog13
+sensor_pin: PK5
 #   T0 on mcu_xye
 smooth_time: 3.0
 control: pid
@@ -160,7 +158,7 @@ max_temp: 270
 
 [probe]
 # Inductive Probe
-pin: ^z:ar19
+pin: ^z:PD2
 #   Z_MAX on mcu_z
 x_offset: 0.0
 y_offset: 25.0
@@ -173,13 +171,13 @@ sample_retract_dist: 6.0
 
 [fan]
 # Print cooling fan
-pin: ar9
+pin: PH6
 #   D9 on mcu_xye
 kick_start_time: 0.500
 
 [heater_fan hotend_fan]
 # Hotend fan
-pin: z:ar9
+pin: z:PH6
 #   D9 on mcu_z
 kick_start_time: 0.500
 heater: extruder
@@ -187,7 +185,7 @@ heater_temp: 50.0
 
 [heater_fan controller_fan]
 # Controller fan
-pin: z:ar10
+pin: z:PB4
 #   D10 on mcu_z
 kick_start_time: 0.500
 heater: heater_bed
@@ -195,17 +193,17 @@ heater_temp: 45.0
 
 [heater_fan exhaust_fan]
 # Exhaust fan
-pin: z:ar8
+pin: z:PH5
 #   D8 on mcu_z
 kick_start_time: 0.500
 heater: heater_bed
 heater_temp: 60.0
 
 [heater_bed]
-heater_pin: z:ar11
+heater_pin: z:PB5
 #   D11 (servo) on mcu_z
 sensor_type: NTC 100K MGB18-104F39050L32
-sensor_pin: z:analog15
+sensor_pin: z:PK7
 #   T2 on mcu_z
 smooth_time: 3.0
 max_power: 0.75
@@ -247,14 +245,14 @@ horizontal_move_z: 6
 [display]
 # RepRapDiscount 128x64 Full Graphic Smart Controller
 lcd_type: st7920
-cs_pin: z:ar16
-sclk_pin: z:ar23
-sid_pin: z:ar17
+cs_pin: z:PH1
+sclk_pin: z:PA1
+sid_pin: z:PH0
 #   LCD connector on mcu_z
 menu_timeout: 40
-encoder_pins: ^z:ar33, ^z:ar31
-click_pin: ^!z:ar35
-kill_pin: ^!z:ar41
+encoder_pins: ^z:PC4, ^z:PC6
+click_pin: ^!z:PC2
+kill_pin: ^!z:PG0
 
 
 ###   Macros   ###