h3n3/klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Deploying to gh-pages from @ Klipper3d/klipper@a8b493a1ae 🚀

Browse Source
This commit is contained in:
KevinOConnor
2024-04-09 20:40:26 +00:00
parent aea6927083
commit 4aee82b247
355 changed files with 6096 additions and 5 deletions
Download Patch File Download Diff File Expand all files Collapse all files

86
G-Codes.html
View File

@@ -1864,6 +1864,33 @@
</ul>
</nav>
</li>
<li class="md-nav__item">
<a href="#probe_eddy_current" class="md-nav__link">
[probe_eddy_current]
</a>
<nav class="md-nav" aria-label="[probe_eddy_current]">
<ul class="md-nav__list">
<li class="md-nav__item">
<a href="#probe_eddy_current_calibrate" class="md-nav__link">
PROBE_EDDY_CURRENT_CALIBRATE
</a>
</li>
<li class="md-nav__item">
<a href="#ldc_calibrate_drive_current" class="md-nav__link">
LDC_CALIBRATE_DRIVE_CURRENT
</a>
</li>
</ul>
</nav>
</li>
<li class="md-nav__item">
@@ -2837,6 +2864,20 @@
<li class="md-nav__item">
<a href="Eddy_Probe.html" class="md-nav__link">
Eddy Current Inductive probe
</a>
</li>
</ul>
</nav>
</li>
@@ -3995,6 +4036,33 @@
</ul>
</nav>
</li>
<li class="md-nav__item">
<a href="#probe_eddy_current" class="md-nav__link">
[probe_eddy_current]
</a>
<nav class="md-nav" aria-label="[probe_eddy_current]">
<ul class="md-nav__list">
<li class="md-nav__item">
<a href="#probe_eddy_current_calibrate" class="md-nav__link">
PROBE_EDDY_CURRENT_CALIBRATE
</a>
</li>
<li class="md-nav__item">
<a href="#ldc_calibrate_drive_current" class="md-nav__link">
LDC_CALIBRATE_DRIVE_CURRENT
</a>
</li>
</ul>
</nav>
</li>
<li class="md-nav__item">
@@ -5305,6 +5373,24 @@ direction as well as Z.</p>
babystepping), and subtract if from the probe's z_offset. This acts
to take a frequently used babystepping value, and "make it permanent".
Requires a <code>SAVE_CONFIG</code> to take effect.</p>
<h3 id="probe_eddy_current">[probe_eddy_current]<a class="headerlink" href="#probe_eddy_current" title="Permanent link">&para;</a></h3>
<p>The following commands are available when a
<a href="Config_Reference.html#probe_eddy_current">probe_eddy_current config section</a>
is enabled.</p>
<h4 id="probe_eddy_current_calibrate">PROBE_EDDY_CURRENT_CALIBRATE<a class="headerlink" href="#probe_eddy_current_calibrate" title="Permanent link">&para;</a></h4>
<p><code>PROBE_EDDY_CURRENT_CALIBRATE CHIP=&lt;config_name&gt;</code>: This starts a tool
that calibrates the sensor resonance frequencies to corresponding Z
heights. The tool will take a couple of minutes to complete. After
completion, use the SAVE_CONFIG command to store the results in the
printer.cfg file.</p>
<h4 id="ldc_calibrate_drive_current">LDC_CALIBRATE_DRIVE_CURRENT<a class="headerlink" href="#ldc_calibrate_drive_current" title="Permanent link">&para;</a></h4>
<p><code>LDC_CALIBRATE_DRIVE_CURRENT CHIP=&lt;config_name&gt;</code> This tool will
calibrate the ldc1612 DRIVE_CURRENT0 register. Prior to using this
tool, move the sensor so that it is near the center of the bed and
about 20mm above the bed surface. Run this command to determine an
appropriate DRIVE_CURRENT for the sensor. After running this command
use the SAVE_CONFIG command to store that new setting in the
printer.cfg config file.</p>
<h3 id="pwm_cycle_time">[pwm_cycle_time]<a class="headerlink" href="#pwm_cycle_time" title="Permanent link">&para;</a></h3>
<p>The following command is available when a
<a href="Config_Reference.html#pwm_cycle_time">pwm_cycle_time config section</a>