Deploying to gh-pages from @ Klipper3d/klipper@96ea871b35 🚀

zh-Hant/Config_Reference.html

@@ -700,6 +700,13 @@
     [skew_correction]
   </a>
   
+</li>
+        
+          <li class="md-nav__item">
+  <a href="#z_thermal_adjust" class="md-nav__link">
+    [z_thermal_adjust]
+  </a>
+  
 </li>
         
       </ul>
@@ -2614,6 +2621,13 @@
     [skew_correction]
   </a>
   
+</li>
+        
+          <li class="md-nav__item">
+  <a href="#z_thermal_adjust" class="md-nav__link">
+    [z_thermal_adjust]
+  </a>
+  
 </li>
         
       </ul>
@@ -4555,6 +4569,38 @@ max_temp:
 <div class="highlight"><pre><span></span><code>[skew_correction]
 </code></pre></div>
 
+<h3 id="z_thermal_adjust">[z_thermal_adjust]<a class="headerlink" href="#z_thermal_adjust" title="Permanent link">&para;</a></h3>
+<p>Temperature-dependant toolhead Z position adjustment. Compensate for vertical toolhead movement caused by thermal expansion of the printer's frame in real-time using a temperature sensor (typically coupled to a vertical section of frame).</p>
+<p>See also: <a href="G-Codes.html#z_thermal_adjust">extended g-code commands</a>.</p>
+<div class="highlight"><pre><span></span><code>[z_thermal_adjust]
+#temp_coeff:
+#   The temperature coefficient of expansion, in mm/degC. For example, a
+#   temp_coeff of 0.01 mm/degC will move the Z axis downwards by 0.01 mm for
+#   every degree Celsius that the temperature sensor increases. Defaults to
+#   0.0 mm/degC, which applies no adjustment.
+#smooth_time:
+#   Smoothing window applied to the temperature sensor, in seconds. Can reduce
+#   motor noise from excessive small corrections in response to sensor noise.
+#   The default is 2.0 seconds.
+#z_adjust_off_above:
+#   Disables adjustments above this Z height [mm]. The last computed correction
+#   will remain applied until the toolhead moves below the specified Z height
+#   again. The default is 99999999.0 mm (always on).
+#max_z_adjustment:
+#   Maximum absolute adjustment that can be applied to the Z axis [mm]. The
+#   default is 99999999.0 mm (unlimited).
+#sensor_type:
+#sensor_pin:
+#min_temp:
+#max_temp:
+#   Temperature sensor configuration.
+#   See the &quot;extruder&quot; section for the definition of the above
+#   parameters.
+#gcode_id:
+#   See the &quot;heater_generic&quot; section for the definition of this
+#   parameter.
+</code></pre></div>
+
 <h2 id="_12">自定義歸零<a class="headerlink" href="#_12" title="Permanent link">&para;</a></h2>
 <h3 id="safe_z_home">[safe_z_home]<a class="headerlink" href="#safe_z_home" title="Permanent link">&para;</a></h3>
 <p>安全 Z 歸位。可以使用這種機制將 Z 軸歸位到特定的 X、Y 坐標。例如，如果工具頭必須在 Z 可以歸位之前移動到床的中心，這很有用。</p>