h3n3/kiauh
1
0
Fork 0
Code Issues 46 Pull Requests 10 Packages Projects Releases Wiki Activity

Stuck instalation Raspberry Pi Zero 2W with Raspberry Pi OS Lite (32bit) BookWorm #459

New Issue
Closed
opened 2024-04-26 00:05:08 +02:00 by JLVFixer · 4 comments
JLVFixer commented 2024-04-26 00:05:08 +02:00 (Migrated from github.com)
Copy Link

Linux Distribution

Raspberry Pi OS Lite (32bit) BookWorm

What happened

I'm experiencing difficulty with the Klipper installation process on my system. It appears to hang indefinitely during the
"Unpacking phase of gcc-arm-none-eabi (15:12.2.rel1-1)". This occurs regardless of the type of SD card used, the power source, or the method used to install the operating system.

What did you expect to happen

Follow through and complete instalation

How to reproduce

Install Rasberry OS Lite with Raspberry Pi Imager 32bit for Raspberry Pi Zero 2W
Configure SSH
Follow the steps provided for KIAUH

Additional information

No response

### Linux Distribution Raspberry Pi OS Lite (32bit) BookWorm ### What happened I'm experiencing difficulty with the Klipper installation process on my system. It appears to hang indefinitely during the "Unpacking phase of gcc-arm-none-eabi (15:12.2.rel1-1)". This occurs regardless of the type of SD card used, the power source, or the method used to install the operating system. ### What did you expect to happen Follow through and complete instalation ### How to reproduce Install Rasberry OS Lite with Raspberry Pi Imager 32bit for Raspberry Pi Zero 2W Configure SSH Follow the steps provided for KIAUH ### Additional information _No response_
sa6kod commented 2024-04-26 06:25:06 +02:00 (Migrated from github.com)
Copy Link

I have the exact same problem,

Recently I got this :
W: Operation was interrupted before it could finish
W: APT had planned for dpkg to do more than it reported back (6 vs 97).
Affected packages: bsdextrautils:armhf eject:armhf fdisk:armhf gcc-arm-none-eabi:armhf libblkid1:armhf libcamera-ipa:armhf libcamera0.2:armhf libfdisk1:armhf libmount1:armhf libpisp-common:armhf libpisp1:armhf libsmartcols1:armhf libuuid1:armhf linux-libc-dev:armhf mount:armhf pi-bluetooth:armhf raspi-config:armhf raspi-firmware:armhf raspi-utils:armhf rfkill:armhf rpicam-apps-lite:armhf util-linux-extra:armhf util-linux:armhf

I have the exact same problem, Recently I got this : W: Operation was interrupted before it could finish W: APT had planned for dpkg to do more than it reported back (6 vs 97). Affected packages: bsdextrautils:armhf eject:armhf fdisk:armhf gcc-arm-none-eabi:armhf libblkid1:armhf libcamera-ipa:armhf libcamera0.2:armhf libfdisk1:armhf libmount1:armhf libpisp-common:armhf libpisp1:armhf libsmartcols1:armhf libuuid1:armhf linux-libc-dev:armhf mount:armhf pi-bluetooth:armhf raspi-config:armhf raspi-firmware:armhf raspi-utils:armhf rfkill:armhf rpicam-apps-lite:armhf util-linux-extra:armhf util-linux:armhf
dw-0 commented 2024-04-26 08:24:17 +02:00 (Migrated from github.com)
Copy Link

This is likely no issue of KIAUH.
With the Information you provided, it seems to point to the system/hardware itself. The Pi Zero 2W was fine a while ago as the absolute minimum. But back then everything already took significantly longer than on a more powerfull Pi. Especially when a fresh system is set up and hundreds of MB are downloaded and unpacked.

This is likely no issue of KIAUH. With the Information you provided, it seems to point to the system/hardware itself. The Pi Zero 2W was fine a while ago as the absolute minimum. But back then everything already took significantly longer than on a more powerfull Pi. Especially when a fresh system is set up and hundreds of MB are downloaded and unpacked.
sa6kod commented 2024-04-26 14:05:02 +02:00 (Migrated from github.com)
Copy Link

I fixed the problem. If you rather install the Mainsail OS on the Rpi it's already preinstalled! This worked for me atleast.

(Operating System) --> "Other specific-purpose OS" --> "3D printing" -->"Mainsail OS"

I fixed the problem. If you rather install the Mainsail OS on the Rpi it's already preinstalled! This worked for me atleast. (Operating System) --> "Other specific-purpose OS" --> "3D printing" -->"Mainsail OS"
nguyencongdanh21 commented 2024-06-01 20:09:16 +02:00 (Migrated from github.com)
Copy Link

Install 64-bit lite OS imager it work fine

Install 64-bit lite OS imager it work fine
Sign in to join this conversation.
No Branch/Tag Specified
Branches Tags
Labels
Clear labels
🐛 bug
Something isn't working
 can't reproduce
➕ community extension
crowsnest
duplicate
This issue or pull request already exists
 ✨ feature request
New feature or request
 fluidd
Something that is fluidd related
 improvement
improvement of existing features/code
 invalid
klipper
Something that is klipper related
 klipperscreen
Something that is klipperscreen related
 mainsail
Something that is mainsail related
 mobileraker
moonraker
Something that is moonraker related
 not kiauh
not planned
octoeverywhere
Something that is OctoEverywhere related
 ❓ question
Further information is requested
 💤 stale
todo
wontfix
This will not be worked on
No Label not kiauh
Milestone
No items
No Milestone
Projects
Clear projects
No project
Assignees
Clear assignees
h3n3
No Assignees
1 Participants
Notifications
Due Date
No due date set.
Dependencies

No dependencies set.

Reference: h3n3/kiauh#459
Delete Branch "%!s()"

Deleting a branch is permanent. Although the deleted branch may continue to exist for a short time before it actually gets removed, it CANNOT be undone in most cases. Continue?