Webui install failure, nginx error #369

New Issue

2023-08-07T19:11:29+02:00

xMxMiller commented

2023-08-07 19:11:29 +02:00

(Migrated from github.com)

Linux Distribution

Armbian 21.11.0-trunk Bullseye

What happened

Tryed to install Mainsail and install failed when attempting to start service.
Tryed Fluid, same issue.
webui install failure.txt

What did you expect to happen

To be brought back to installation menu page after the webui had been installed.

How to reproduce

Follow install guide.

Additional information

Mellow gemini Fly v3 control board I got in a Siboor v0.2 r1 kit.

### Linux Distribution Armbian 21.11.0-trunk Bullseye ### What happened Tryed to install Mainsail and install failed when attempting to start service. Tryed Fluid, same issue. [webui install failure.txt](https://github.com/th33xitus/kiauh/files/12283279/webui.install.failure.txt) ### What did you expect to happen To be brought back to installation menu page after the webui had been installed. ### How to reproduce Follow install guide. ### Additional information Mellow gemini Fly v3 control board I got in a Siboor v0.2 r1 kit.

dw-0 commented

2023-08-07 20:09:48 +02:00

(Migrated from github.com)

The issue is the following:

Aug 07 16:57:12 voron-0 nginx[2084]: nginx: [emerg] open() "/etc/nginx/sites-enabled/klipper_webui" failed (2: No such file or directory) in /etc/nginx/nginx.conf:60

That is no file that gets installed with KIAUH.
You say that you're using a Fly Gemini, so are you using their Image as well? Afaik they have both interfaces already installed and you select one depending on which you have activated in a special config file. I don't know which it was from the top of my head, but they do it kinda differently than KIAUH would install and configure NGINX for the use of Mainsail or Fluidd.

Apart from that i see an issue with not enough space left on the device, so you might want to check that as well.

The issue is the following: ``` Aug 07 16:57:12 voron-0 nginx[2084]: nginx: [emerg] open() "/etc/nginx/sites-enabled/klipper_webui" failed (2: No such file or directory) in /etc/nginx/nginx.conf:60 ``` That is no file that gets installed with KIAUH. You say that you're using a Fly Gemini, so are you using their Image as well? Afaik they have both interfaces already installed and you select one depending on which you have activated in a special config file. I don't know which it was from the top of my head, but they do it kinda differently than KIAUH would install and configure NGINX for the use of Mainsail or Fluidd. Apart from that i see an issue with not enough space left on the device, so you might want to check that as well.

xMxMiller commented

2023-08-07 20:29:01 +02:00

(Migrated from github.com)

Cheers for looking at this,

I am running the image it had pre-installed and wanted to use kiauh to make sure everything was upto date aswell as change from Fluid to Mainsail.
Im about to re-image to the original FLYOS.

On Aug 7 2023, at 7:09 pm, th33xitus @.***> wrote:

The issue is the following:
Aug 07 16:57:12 voron-0 nginx[2084]: nginx: [emerg] open() "/etc/nginx/sites-enabled/klipper_webui" failed (2: No such file or directory) in /etc/nginx/nginx.conf:60
That is no file that gets installed with KIAUH.
You say that you're using a Fly Gemini, so are you using their Image as well? Afaik they have both interfaces already installed and you select one depending on which you have activated in a special config file. I don't know which it was from the top of my head, but they do it kinda differently than KIAUH would install and configure NGINX for the use of Mainsail or Fluidd.

—
Reply to this email directly, view it on GitHub (https://github.com/th33xitus/kiauh/issues/369#issuecomment-1668362276), or unsubscribe (https://github.com/notifications/unsubscribe-auth/AWDGPKE3LTJUTRJSQMNSSKDXUEVPPANCNFSM6AAAAAA3HI7AOU).
You are receiving this because you authored the thread.

Cheers for looking at this, I am running the image it had pre-installed and wanted to use kiauh to make sure everything was upto date aswell as change from Fluid to Mainsail. Im about to re-image to the original FLYOS. On Aug 7 2023, at 7:09 pm, th33xitus ***@***.***> wrote: > > > The issue is the following: > Aug 07 16:57:12 voron-0 nginx[2084]: nginx: [emerg] open() "/etc/nginx/sites-enabled/klipper_webui" failed (2: No such file or directory) in /etc/nginx/nginx.conf:60 > That is no file that gets installed with KIAUH. > You say that you're using a Fly Gemini, so are you using their Image as well? Afaik they have both interfaces already installed and you select one depending on which you have activated in a special config file. I don't know which it was from the top of my head, but they do it kinda differently than KIAUH would install and configure NGINX for the use of Mainsail or Fluidd. > > > — > Reply to this email directly, view it on GitHub (https://github.com/th33xitus/kiauh/issues/369#issuecomment-1668362276), or unsubscribe (https://github.com/notifications/unsubscribe-auth/AWDGPKE3LTJUTRJSQMNSSKDXUEVPPANCNFSM6AAAAAA3HI7AOU). > You are receiving this because you authored the thread. >

dw-0 commented

2023-08-07 20:33:59 +02:00

(Migrated from github.com)

Check out the following guide:
https://3dpandme.com/2022/07/11/mellow-fly-gemini-v2-installation-guide-for-voron-0-1/

And search for "Swapping to Mainsail" in this guide. This explains what file you need to edit, to switch from Fluidd to Mainsail and vice versa. Using KIAUH on their image to try and uninstall the one, and installing the other won't work. They somehow manage to overwrite everything during the next boot and revert all changes made iirc.

Check out the following guide: https://3dpandme.com/2022/07/11/mellow-fly-gemini-v2-installation-guide-for-voron-0-1/ And search for "Swapping to Mainsail" in this guide. This explains what file you need to edit, to switch from Fluidd to Mainsail and vice versa. Using KIAUH on their image to try and uninstall the one, and installing the other won't work. They somehow manage to overwrite everything during the next boot and revert all changes made iirc.

xMxMiller commented

2023-08-07 21:56:46 +02:00

(Migrated from github.com)

Thanks for all your help even though my issue was unrelated to your project

On Aug 7 2023, at 7:34 pm, th33xitus @.***> wrote:

Check out the following guide:
https://3dpandme.com/2022/07/11/mellow-fly-gemini-v2-installation-guide-for-voron-0-1/

And search for "Swapping to Mainsail" in this guide. This explains what file you need to edit, to switch from Fluidd to Mainsail and vice versa. Using KIAUH on their image to try and uninstall the one, and installing the other won't work. They somehow manage to overwrite everything during the next boot and revert all changes made iirc.
—
Reply to this email directly, view it on GitHub (https://github.com/th33xitus/kiauh/issues/369#issuecomment-1668395523), or unsubscribe (https://github.com/notifications/unsubscribe-auth/AWDGPKDSOD4PHITSYIKLPSTXUEYKFANCNFSM6AAAAAA3HI7AOU).
You are receiving this because you authored the thread.

Thanks for all your help even though my issue was unrelated to your project On Aug 7 2023, at 7:34 pm, th33xitus ***@***.***> wrote: > > > Check out the following guide: > https://3dpandme.com/2022/07/11/mellow-fly-gemini-v2-installation-guide-for-voron-0-1/ > > > And search for "Swapping to Mainsail" in this guide. This explains what file you need to edit, to switch from Fluidd to Mainsail and vice versa. Using KIAUH on their image to try and uninstall the one, and installing the other won't work. They somehow manage to overwrite everything during the next boot and revert all changes made iirc. > — > Reply to this email directly, view it on GitHub (https://github.com/th33xitus/kiauh/issues/369#issuecomment-1668395523), or unsubscribe (https://github.com/notifications/unsubscribe-auth/AWDGPKDSOD4PHITSYIKLPSTXUEYKFANCNFSM6AAAAAA3HI7AOU). > You are receiving this because you authored the thread. >

👍 1

Sign in to join this conversation.

1 Participants

Notifications

Due Date

No due date set.

Dependencies

No dependencies set.

Reference: h3n3/kiauh#369