Klemmen toegevoegd

multiconnect/connectorHoleClamp.py

@@ -24,7 +24,8 @@ lp6 = line_point_6 = ttc+tt
 pts = [
         (0, 0),
         (cw, 0),
-        (cw, dc),
+        (cw, dc-0.5),
+        (cw-1.2, dc),
         (lp5, dc),
         (lp5, (dc+tt+ttc-dcs)),
         (lp5+(5/2), (dc+tt+ttc-dcs)),
@@ -39,5 +40,7 @@ with BuildPart() as clamp:
             Polyline(pts)
         make_face()
     extrude(amount = cw)
+    fillet(clamp.edges(), radius = 0.2)
 
+export_stl(clamp.part, "connectorHoleClamp.stl")
 show_all()

multiconnect/connectorHoleLockingPin.py

@@ -0,0 +1,37 @@
+from ocp_vscode import *
+from build123d import *
+set_port(3939)
+
+tt = thickness_toolboard = 0.8
+lsp = length_straight_part = 5.0
+tb = thickness_bevel = 2.5
+teub = thickness_edge_until_board = 0.5
+wbs = width_board_side = 15.0
+ttc = thickness_total_connector = 4.0
+cw = clamp_width = 9.8
+rc = rotation_clamp = 45.0
+dc = depth_clamp = 4.0
+dcs = depth_clamp_space = 1.6
+tlp = thickness_locking_pin = cw*0.25
+lcr = length_clamp_room = cw+5
+
+pts = [
+        (0, 0),
+        ((tlp+2.5), 0),
+        ((tlp+2.5), dcs),
+        (tlp, dcs),
+        (tlp, (dc+tt+ttc)),
+        (0, (dc+tt+ttc)),
+        (0, 0)
+]
+
+with BuildPart() as clampLock:
+    with BuildSketch() as sk_clampLock:
+        with BuildLine() as ln_clampLock:
+            Polyline(pts)
+        make_face()
+    extrude(amount = cw)
+    fillet(clampLock.edges(), radius = 0.2)
+
+export_step(clampLock.part, "connectorHoleClampLock.step")
+show_all()

multiconnect/connectorWithHole.py

@@ -4,15 +4,12 @@ set_port(3939)
 
 tt = thickness_toolboard = 0.8
 wc = width_connector = 20.0
-lsp = length_straight_part = 5.0
 tb = thickness_bevel = 2.5
 teub = thickness_edge_until_board = 0.5
-wbs = width_board_side = 15.0
 ttc = thickness_total_connector = 4.0
 cw = clamp_width = 9.8
-rc = rotation_clamp = 45.0
-dc = depth_clamp = 4.0
 dcr = depth_clamp_room = 1.6
+lcr = length_clamp_room = cw+5
 
 with BuildPart() as connector:
     with BuildSketch() as connector_sk:
@@ -24,9 +21,9 @@ with BuildPart() as connector:
         Rectangle(cw+0.1, cw+0.1)
     extrude(amount = -ttc, mode=Mode.SUBTRACT)
     with BuildSketch(connector.faces().sort_by(Axis.Z)[0]):
-        Rectangle(cw+5, cw+0.1)
+        Rectangle(lcr, cw+0.1)
     extrude(amount = -dcr, mode=Mode.SUBTRACT)
 
 
-export_stl(connector.part, "connectorWithHole.stl")
+#export_stl(connector.part, "connectorWithHole.stl")
 show_all()