285 lines
6.1 KiB
INI
285 lines
6.1 KiB
INI
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
|
# E3 v1.2. To use this config, the firmware should be compiled for the
|
|
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
|
# select "Enable extra low-level configuration options" and configure
|
|
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
|
|
|
# The "make flash" command does not work on the SKR mini E3. Instead,
|
|
# after running "make", copy the generated "out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the SKR
|
|
# mini E3 with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
# Note: This board has a design flaw in its thermistor circuits that
|
|
# cause inaccurate temperatures (most noticeable at low temperatures).
|
|
|
|
# Met de DropEffect OmniDrop V2.1 is het punt links-beneden (dus het 0-punt): X = 12 en Y = 30
|
|
# En om bij de clips vandaan te blijven wordt er aan Y nog 21 toegevoegd.
|
|
|
|
# Invoegen van de standaard macros, geknipt uit printer.cfg
|
|
#[include macros/standaardMacros.cfg]
|
|
# Invoegen van macros. Deze komen uit: https://github.com/jschuh/klipper-macros
|
|
[include macros/jschuh_macros.cfg]
|
|
[include scherm/menu.cfg]
|
|
[include leds/neopixel.cfg]
|
|
|
|
[exclude_object]
|
|
|
|
[stepper_x]
|
|
step_pin: PB13
|
|
dir_pin: !PB12
|
|
enable_pin: !PB14
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PC0
|
|
position_endstop: -13.5
|
|
position_min: -13.5
|
|
position_max: 221.5
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PB15
|
|
run_current: 0.580
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 250
|
|
|
|
[stepper_y]
|
|
step_pin: PB10
|
|
dir_pin: !PB2
|
|
enable_pin: !PB11
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PC1
|
|
position_endstop: -51
|
|
position_min: -51
|
|
position_max: 195
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PC6
|
|
run_current: 0.580
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 250
|
|
|
|
[stepper_z]
|
|
step_pin: PB0
|
|
dir_pin: PC5
|
|
enable_pin: !PB1
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^PC2
|
|
position_endstop: 0
|
|
position_min: -2
|
|
position_max: 250
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC10
|
|
run_current: 0.580
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 5
|
|
|
|
[bltouch]
|
|
sensor_pin: ^PC14
|
|
control_pin: PA1
|
|
#pin_up_reports_not_triggered: False
|
|
#pin_up_touch_mode_reports_triggered: False
|
|
x_offset: 33.7
|
|
y_offset: -33.5
|
|
#z_offset: 2.68
|
|
pin_move_time: 0.680
|
|
|
|
[bed_screws]
|
|
screw1: 29,31
|
|
screw2: 196,31
|
|
screw3: 196,206
|
|
screw4: 29,206
|
|
#screw5: 117,117
|
|
|
|
[bed_mesh]
|
|
speed: 80
|
|
horizontal_move_z: 5
|
|
mesh_min: 25,10
|
|
mesh_max: 200,150
|
|
probe_count: 5,5
|
|
|
|
[extruder]
|
|
# DropEffect OmniaDrop V2.1
|
|
step_pin: PB3
|
|
dir_pin: PB4
|
|
enable_pin: !PD2
|
|
microsteps: 16
|
|
gear_ratio: 5:1
|
|
rotation_distance: 32.160
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PC8
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA0
|
|
#control: pid
|
|
#pid_Kp: 21.527
|
|
#pid_Ki: 1.063
|
|
#pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 285
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC11
|
|
run_current: 0.500
|
|
hold_current: 0.400
|
|
stealthchop_threshold: 5
|
|
|
|
[heater_fan my_nozzle_fan]
|
|
# Aansturing via PT-DET pinout
|
|
pin: PC12
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
fan_speed: 1.0
|
|
|
|
[heater_bed]
|
|
heater_pin: PC9
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC3
|
|
#control: pid
|
|
#pid_Kp: 54.027
|
|
#pid_Ki: 0.770
|
|
#pid_Kd: 948.182
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PA8
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[static_digital_output usb_pullup_enable]
|
|
pins: !PC13
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
|
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: EXP1_7
|
|
sclk_pin: EXP1_6
|
|
sid_pin: EXP1_8
|
|
encoder_pins: ^EXP1_5, ^EXP1_3
|
|
click_pin: ^!EXP1_2
|
|
|
|
[output_pin beeper]
|
|
pin: EXP1_1
|
|
|
|
[virtual_sdcard]
|
|
path: ~/printer_data/gcodes
|
|
on_error_gcode: CANCEL_PRINT
|
|
|
|
[display_status]
|
|
|
|
[mcu rpi]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[adxl345]
|
|
cs_pin: rpi:None
|
|
|
|
[resonance_tester]
|
|
accel_chip: adxl345
|
|
probe_points:
|
|
100, 100, 20 # an example
|
|
|
|
### input-shaper waardes verkregen via adxl345 tuning
|
|
[input_shaper]
|
|
shaper_freq_x: 69.8
|
|
shaper_type_x: mzv
|
|
shaper_freq_y: 41.4
|
|
shaper_type_y: ei
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 30.552
|
|
#*# pid_ki = 2.289
|
|
#*# pid_kd = 101.966
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 61.642
|
|
#*# pid_ki = 0.561
|
|
#*# pid_kd = 1694.375
|
|
#*#
|
|
#*# [bltouch]
|
|
#*# z_offset = 2.675
|
|
#*#
|
|
#*# [stepper_z]
|
|
#*#
|
|
#*# [bed_mesh GlasbedCarbonBoven]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.250000, 0.085000, 0.025000, -0.015000, -0.027500
|
|
#*# 0.192500, 0.072500, 0.015000, -0.015000, -0.045000
|
|
#*# 0.052500, -0.032500, -0.037500, -0.050000, 0.015000
|
|
#*# -0.030000, -0.017500, 0.025000, 0.072500, 0.117500
|
|
#*# 0.032500, 0.005000, 0.042500, 0.032500, 0.127500
|
|
#*# tension = 0.2
|
|
#*# min_x = 25.0
|
|
#*# algo = lagrange
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 10.0
|
|
#*# x_count = 5
|
|
#*# max_y = 170.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 200.0
|
|
#*#
|
|
#*# [bed_mesh GlasbedCarbonBoven ]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.030000, -0.065000, -0.075000, -0.145000, -0.165000
|
|
#*# 0.272500, 0.092500, -0.070000, -0.275000, -0.422500
|
|
#*# 0.027500, -0.052500, -0.075000, -0.165000, -0.160000
|
|
#*# -0.045000, -0.040000, -0.045000, -0.105000, -0.057500
|
|
#*# 0.017500, 0.005000, 0.022500, -0.012500, 0.002500
|
|
#*# tension = 0.2
|
|
#*# min_x = 25.0
|
|
#*# algo = lagrange
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 10.0
|
|
#*# x_count = 5
|
|
#*# max_y = 170.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 200.0
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# -0.327500, -0.370000, -0.362500, -0.365000, -0.490000
|
|
#*# -0.285000, -0.327500, -0.385000, -0.417500, -0.482500
|
|
#*# -0.442500, -0.385000, -0.335000, -0.302500, -0.357500
|
|
#*# -0.460000, -0.382500, -0.365000, -0.307500, -0.282500
|
|
#*# -0.405000, -0.302500, -0.257500, -0.222500, -0.240000
|
|
#*# tension = 0.2
|
|
#*# min_x = 25.0
|
|
#*# algo = lagrange
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 10.0
|
|
#*# x_count = 5
|
|
#*# max_y = 170.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 200.0
|