1010 lines
25 KiB
INI
1010 lines
25 KiB
INI
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
|
# E3 v1.2. To use this config, the firmware should be compiled for the
|
|
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
|
# select "Enable extra low-level configuration options" and configure
|
|
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
|
|
|
# The "make flash" command does not work on the SKR mini E3. Instead,
|
|
# after running "make", copy the generated "out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the SKR
|
|
# mini E3 with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
# Note: This board has a design flaw in its thermistor circuits that
|
|
# cause inaccurate temperatures (most noticeable at low temperatures).
|
|
|
|
# Met de DropEffect OmniDrop V2.1 is het punt links-beneden (dus het 0-punt): X = 12 en Y = 30
|
|
|
|
# Invoegen van macros. Deze komen uit: https://github.com/jschuh/klipper-macros
|
|
[include jschuh_macros.cfg]
|
|
|
|
[stepper_x]
|
|
step_pin: PB13
|
|
dir_pin: !PB12
|
|
enable_pin: !PB14
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PC0
|
|
position_endstop: -13.5
|
|
position_min: -13.5
|
|
position_max: 221.5
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PB15
|
|
run_current: 0.580
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 250
|
|
|
|
[stepper_y]
|
|
step_pin: PB10
|
|
dir_pin: !PB2
|
|
enable_pin: !PB11
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PC1
|
|
position_endstop: -9
|
|
position_min: -9
|
|
position_max: 226
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PC6
|
|
run_current: 0.580
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 250
|
|
|
|
[stepper_z]
|
|
step_pin: PB0
|
|
dir_pin: PC5
|
|
enable_pin: !PB1
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^PC2
|
|
position_endstop: 0
|
|
position_max: 250
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC10
|
|
run_current: 0.580
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 5
|
|
|
|
[bltouch]
|
|
sensor_pin: ^PC14
|
|
control_pin: PA1
|
|
#pin_up_reports_not_triggered: False
|
|
#pin_up_touch_mode_reports_triggered: False
|
|
x_offset: 33.7
|
|
y_offset: -33.5
|
|
#z_offset: 2.68
|
|
pin_move_time: 0.680
|
|
|
|
[bed_screws]
|
|
screw1: 29,31
|
|
screw2: 196,31
|
|
screw3: 196,206
|
|
screw4: 29,206
|
|
#screw5: 117,117
|
|
|
|
[bed_mesh]
|
|
speed: 80
|
|
horizontal_move_z: 5
|
|
mesh_min: 25,10
|
|
mesh_max: 200,170
|
|
probe_count: 5,5
|
|
|
|
[extruder]
|
|
# DropEffect OmniaDrop V2.1
|
|
step_pin: PB3
|
|
dir_pin: PB4
|
|
enable_pin: !PD2
|
|
microsteps: 16
|
|
gear_ratio: 5:1
|
|
rotation_distance: 32.160
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PC8
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA0
|
|
#control: pid
|
|
#pid_Kp: 21.527
|
|
#pid_Ki: 1.063
|
|
#pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 285
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC11
|
|
run_current: 0.500
|
|
hold_current: 0.400
|
|
stealthchop_threshold: 5
|
|
|
|
[heater_fan my_nozzle_fan]
|
|
# Aansturing via PT-DET pinout
|
|
pin: PC12
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
fan_speed: 1.0
|
|
|
|
[heater_bed]
|
|
heater_pin: PC9
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC3
|
|
#control: pid
|
|
#pid_Kp: 54.027
|
|
#pid_Ki: 0.770
|
|
#pid_Kd: 948.182
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PA8
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[neopixel ledjes]
|
|
pin: PC7
|
|
# The pin connected to the neopixel. This parameter must be
|
|
# provided.
|
|
chain_count: 6
|
|
# The number of Neopixel chips that are "daisy chained" to the
|
|
# provided pin. The default is 1 (which indicates only a single
|
|
# Neopixel is connected to the pin).
|
|
color_order: GRB
|
|
# Set the pixel order required by the LED hardware (using a string
|
|
# containing the letters R, G, B, W with W optional). Alternatively,
|
|
# this may be a comma separated list of pixel orders - one for each
|
|
# LED in the chain. The default is GRB.
|
|
initial_RED: 1.0
|
|
initial_GREEN: 1.0
|
|
initial_BLUE: 1.0
|
|
#initial_WHITE: 0.0
|
|
# See the "led" section for information on these parameters.
|
|
|
|
#[include neopixels.cfg]
|
|
|
|
[static_digital_output usb_pullup_enable]
|
|
pins: !PC13
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
|
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: EXP1_7
|
|
sclk_pin: EXP1_6
|
|
sid_pin: EXP1_8
|
|
encoder_pins: ^EXP1_5, ^EXP1_3
|
|
click_pin: ^!EXP1_2
|
|
|
|
[output_pin beeper]
|
|
pin: EXP1_1
|
|
|
|
[virtual_sdcard]
|
|
path: ~/printer_data/gcodes
|
|
|
|
[display_status]
|
|
|
|
[pause_resume]
|
|
|
|
[gcode_macro PAUSE]
|
|
description: Pause the actual running print
|
|
rename_existing: PAUSE_BASE
|
|
# change this if you need more or less extrusion
|
|
variable_extrude: 1.0
|
|
gcode:
|
|
##### read E from pause macro #####
|
|
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
|
##### set park positon for x and y #####
|
|
# default is your max posion from your printer.cfg
|
|
{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
|
|
{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
|
|
##### calculate save lift position #####
|
|
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
|
{% set act_z = printer.toolhead.position.z|float %}
|
|
{% if act_z < (max_z - 2.0) %}
|
|
{% set z_safe = 2.0 %}
|
|
{% else %}
|
|
{% set z_safe = max_z - act_z %}
|
|
{% endif %}
|
|
##### end of definitions #####
|
|
PAUSE_BASE
|
|
G91
|
|
{% if printer.extruder.can_extrude|lower == 'true' %}
|
|
G1 E-{E} F2100
|
|
{% else %}
|
|
{action_respond_info("Extruder not hot enough")}
|
|
{% endif %}
|
|
{% if "xyz" in printer.toolhead.homed_axes %}
|
|
G1 Z{z_safe} F900
|
|
G90
|
|
G1 X{x_park} Y{y_park} F6000
|
|
{% else %}
|
|
{action_respond_info("Printer not homed")}
|
|
{% endif %}
|
|
|
|
[gcode_macro RESUME]
|
|
description: Resume the actual running print
|
|
rename_existing: RESUME_BASE
|
|
gcode:
|
|
##### read E from pause macro #####
|
|
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
|
#### get VELOCITY parameter if specified ####
|
|
{% if 'VELOCITY' in params|upper %}
|
|
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
|
{%else %}
|
|
{% set get_params = "" %}
|
|
{% endif %}
|
|
##### end of definitions #####
|
|
{% if printer.extruder.can_extrude|lower == 'true' %}
|
|
G91
|
|
G1 E{E} F2100
|
|
{% else %}
|
|
{action_respond_info("Extruder not hot enough")}
|
|
{% endif %}
|
|
RESUME_BASE {get_params}
|
|
|
|
[gcode_macro CANCEL_PRINT]
|
|
description: Cancel the actual running print
|
|
rename_existing: CANCEL_PRINT_BASE
|
|
gcode:
|
|
TURN_OFF_HEATERS
|
|
CANCEL_PRINT_BASE
|
|
|
|
# The print bed can move so far to the front, that the nozzle can reach the
|
|
# plastic cover of the print bed heater cable (only when the bed is moved by
|
|
# hand). By homing the Y axis before the X axis, it is ensured the nozzle will
|
|
# not melt through the plastic part.
|
|
# BEWARE: You will lose the ability to home axes individually. The printer will
|
|
# always home all axes for every G28 command.
|
|
#[homing_override]
|
|
#gcode:
|
|
# G28 Y0
|
|
# G28 X0
|
|
# G28 Z0
|
|
|
|
# ================================================================================
|
|
# GCode Macro: START_PRINT
|
|
# Add START_PRINT in your slicers starting script.
|
|
# ================================================================================
|
|
[gcode_macro START_PRINT]
|
|
gcode:
|
|
G28; Home all axes
|
|
BED_MESH_CALIBRATE
|
|
G92 E0; Reset Extruder
|
|
G1 Z25.0 F3000; Move Z Axis up little to prevent scratching of Heat Bed
|
|
G1 X0.1 Y20 Z0.3 F5000.0; Move to start position
|
|
G1 X0.1 Y200.0 Z0.3 F1500.0 E15; Draw the first line
|
|
G1 X0.4 Y200.0 Z0.3 F5000.0; Move to side a little
|
|
G1 X0.4 Y20 Z0.3 F1500.0 E30; Draw the second line
|
|
G92 E0; Reset Extruder
|
|
G1 Z25.0 F3000; Move Z Axis up little to prevent scratching of Heat Bed
|
|
M118 punt gcode_macro START_PRINT
|
|
|
|
# ================================================================================
|
|
# GCode Macro: END_PRINT
|
|
# Add END_PRINT in your slicers ending script
|
|
# ================================================================================
|
|
[gcode_macro END_PRINT]
|
|
gcode:
|
|
G91; Relative Positioning
|
|
G1 Z+10; Move Z up so it doesn't hit anything
|
|
G90; Absolute Positioning
|
|
G1 Y190 F1500; bring Y up front
|
|
# G10 ; set tool offset? or retract?
|
|
# G1 E-10 F300; Retrack-10
|
|
G1 X10 Y220 F2000; Move to X10, Y220
|
|
M104 S0; Turn off Extruder temperature (set it to 0)
|
|
M140 S0; Turn off Bed temperature (set it to 0)
|
|
M106 S0; turn off cooling fan
|
|
M84; Disable steppers
|
|
# ================================================================================
|
|
# GCode Macro G29
|
|
# Fires when G29 is sent to the printer
|
|
# ================================================================================
|
|
#[gcode_macro G29]
|
|
#gcode:
|
|
# G1 Z10 F600
|
|
# G4 P200
|
|
# G1 Z10 F600
|
|
# G4 P100
|
|
|
|
### Raspberry Pi als MCU om de GPIO te gebruiken voor in- en output
|
|
|
|
[mcu rpi]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[adxl345]
|
|
cs_pin: rpi:None
|
|
|
|
[resonance_tester]
|
|
accel_chip: adxl345
|
|
probe_points:
|
|
100, 100, 20 # an example
|
|
|
|
### input-shaper waardes verkregen via adxl345 tuning
|
|
[input_shaper]
|
|
shaper_freq_x: 69.8
|
|
shaper_type_x: mzv
|
|
shaper_freq_y: 41.4
|
|
shaper_type_y: ei
|
|
|
|
### menu main ###
|
|
[menu __main]
|
|
type: list
|
|
name: Main
|
|
|
|
### menu tune ###
|
|
[menu __main __tune]
|
|
type: list
|
|
enable: {printer.idle_timeout.state == "Printing"}
|
|
name: Afstellen
|
|
|
|
[menu __main __tune __speed]
|
|
type: input
|
|
name: Snelheid: {'%3d' % (menu.input*100)}%
|
|
input: {printer.gcode_move.speed_factor}
|
|
input_min: 0.01
|
|
input_max: 5
|
|
input_step: 0.01
|
|
realtime: True
|
|
gcode:
|
|
M220 S{'%d' % (menu.input*100)}
|
|
|
|
[menu __main __tune __flow]
|
|
type: input
|
|
name: Flow: {'%3d' % (menu.input*100)}%
|
|
input: {printer.gcode_move.extrude_factor}
|
|
input_min: 0.01
|
|
input_max: 2
|
|
input_step: 0.01
|
|
realtime: True
|
|
gcode:
|
|
M221 S{'%d' % (menu.input*100)}
|
|
|
|
[menu __main __tune __offsetz]
|
|
type: input
|
|
name: Offset Z:{'%05.3f' % menu.input}
|
|
input: {printer.gcode_move.homing_origin.z}
|
|
input_min: -5
|
|
input_max: 5
|
|
input_step: 0.005
|
|
realtime: True
|
|
gcode:
|
|
SET_GCODE_OFFSET Z={'%.3f' % menu.input} MOVE=1
|
|
|
|
### menu virtual sdcard ###
|
|
[menu __main __sdcard]
|
|
type: vsdlist
|
|
enable: {('virtual_sdcard' in printer)}
|
|
name: SD Kaart
|
|
|
|
[menu __main __sdcard __start]
|
|
type: command
|
|
enable: {('virtual_sdcard' in printer) and printer.virtual_sdcard.file_path and not printer.virtual_sdcard.is_active}
|
|
name: Start printen
|
|
gcode: M24
|
|
|
|
[menu __main __sdcard __resume]
|
|
type: command
|
|
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "paused"}
|
|
name: Herstart printen
|
|
gcode:
|
|
{% if "pause_resume" in printer %}
|
|
RESUME
|
|
{% else %}
|
|
M24
|
|
{% endif %}
|
|
|
|
[menu __main __sdcard __pause]
|
|
type: command
|
|
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "printing"}
|
|
name: Pauseer printen
|
|
gcode:
|
|
{% if "pause_resume" in printer %}
|
|
PAUSE
|
|
{% else %}
|
|
M25
|
|
{% endif %}
|
|
|
|
[menu __main __sdcard __cancel]
|
|
type: command
|
|
enable: {('virtual_sdcard' in printer) and (printer.print_stats.state == "printing" or printer.print_stats.state == "paused")}
|
|
name: Annuleer printen
|
|
gcode:
|
|
{% if 'pause_resume' in printer %}
|
|
CANCEL_PRINT
|
|
{% else %}
|
|
M25
|
|
M27
|
|
M26 S0
|
|
TURN_OFF_HEATERS
|
|
{% if printer.toolhead.position.z <= printer.toolhead.axis_maximum.z - 5 %}
|
|
G91
|
|
G0 Z5 F1000
|
|
G90
|
|
{% endif %}
|
|
{% endif %}
|
|
|
|
### menu control ###
|
|
[menu __main __control]
|
|
type: list
|
|
name: Control
|
|
|
|
[menu __main __control __home]
|
|
type: command
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Home All
|
|
gcode: G28
|
|
|
|
[menu __main __control __homez]
|
|
type: command
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Home Z
|
|
gcode: G28 Z
|
|
|
|
[menu __main __control __homexy]
|
|
type: command
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Home X/Y
|
|
gcode: G28 X Y
|
|
|
|
[menu __main __control __disable]
|
|
type: command
|
|
name: Steppers uit
|
|
gcode:
|
|
M84
|
|
M18
|
|
|
|
[menu __main __control __fanonoff]
|
|
type: input
|
|
enable: {'fan' in printer}
|
|
name: Koeling: {'ON ' if menu.input else 'OFF'}
|
|
input: {printer.fan.speed}
|
|
input_min: 0
|
|
input_max: 1
|
|
input_step: 1
|
|
gcode:
|
|
M106 S{255 if menu.input else 0}
|
|
|
|
[menu __main __control __fanspeed]
|
|
type: input
|
|
enable: {'fan' in printer}
|
|
name: Snelheid koeler: {'%3d' % (menu.input*100)}%
|
|
input: {printer.fan.speed}
|
|
input_min: 0
|
|
input_max: 1
|
|
input_step: 0.01
|
|
gcode:
|
|
M106 S{'%d' % (menu.input*255)}
|
|
|
|
[menu __main __control __caselightonoff]
|
|
type: input
|
|
enable: {'output_pin caselight' in printer}
|
|
name: Verlichting: {'ON ' if menu.input else 'OFF'}
|
|
input: {printer['output_pin caselight'].value}
|
|
input_min: 0
|
|
input_max: 1
|
|
input_step: 1
|
|
gcode:
|
|
SET_PIN PIN=caselight VALUE={1 if menu.input else 0}
|
|
|
|
[menu __main __control __caselightpwm]
|
|
type: input
|
|
enable: {'output_pin caselight' in printer}
|
|
name: Verlichting: {'%3d' % (menu.input*100)}%
|
|
input: {printer['output_pin caselight'].value}
|
|
input_min: 0.0
|
|
input_max: 1.0
|
|
input_step: 0.01
|
|
gcode:
|
|
SET_PIN PIN=caselight VALUE={menu.input}
|
|
|
|
### menu move 10mm ###
|
|
[menu __main __control __move_10mm]
|
|
type: list
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Verplaats 10mm
|
|
|
|
[menu __main __control __move_10mm __axis_x]
|
|
type: input
|
|
name: Verplaats X:{'%05.1f' % menu.input}
|
|
input: {printer.gcode_move.gcode_position.x}
|
|
input_min: {printer.toolhead.axis_minimum.x}
|
|
input_max: {printer.toolhead.axis_maximum.x}
|
|
input_step: 10.0
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
G90
|
|
G1 X{menu.input}
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
[menu __main __control __move_10mm __axis_y]
|
|
type: input
|
|
name: Verplaats Y:{'%05.1f' % menu.input}
|
|
input: {printer.gcode_move.gcode_position.y}
|
|
input_min: {printer.toolhead.axis_minimum.y}
|
|
input_max: {printer.toolhead.axis_maximum.y}
|
|
input_step: 10.0
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
G90
|
|
G1 Y{menu.input}
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
[menu __main __control __move_10mm __axis_z]
|
|
type: input
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Verplaats Z:{'%05.1f' % menu.input}
|
|
input: {printer.gcode_move.gcode_position.z}
|
|
input_min: 0
|
|
input_max: {printer.toolhead.axis_maximum.z}
|
|
input_step: 10.0
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
G90
|
|
G1 Z{menu.input}
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
[menu __main __control __move_10mm __axis_e]
|
|
type: input
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Draai E:{'%+06.1f' % menu.input}
|
|
input: 0
|
|
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
input_step: 10.0
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
M83
|
|
G1 E{menu.input} F240
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
### menu move 1mm ###
|
|
[menu __main __control __move_1mm]
|
|
type: list
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Verplaats 1mm
|
|
|
|
[menu __main __control __move_1mm __axis_x]
|
|
type: input
|
|
name: Verplaats X:{'%05.1f' % menu.input}
|
|
input: {printer.gcode_move.gcode_position.x}
|
|
input_min: {printer.toolhead.axis_minimum.x}
|
|
input_max: {printer.toolhead.axis_maximum.x}
|
|
input_step: 1.0
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
G90
|
|
G1 X{menu.input}
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
[menu __main __control __move_1mm __axis_y]
|
|
type: input
|
|
name: Verplaats Y:{'%05.1f' % menu.input}
|
|
input: {printer.gcode_move.gcode_position.y}
|
|
input_min: {printer.toolhead.axis_minimum.y}
|
|
input_max: {printer.toolhead.axis_maximum.y}
|
|
input_step: 1.0
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
G90
|
|
G1 Y{menu.input}
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
[menu __main __control __move_1mm __axis_z]
|
|
type: input
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Verplaats Z:{'%05.1f' % menu.input}
|
|
input: {printer.gcode_move.gcode_position.z}
|
|
input_min: 0
|
|
input_max: {printer.toolhead.axis_maximum.z}
|
|
input_step: 1.0
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
G90
|
|
G1 Z{menu.input}
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
[menu __main __control __move_1mm __axis_e]
|
|
type: input
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Draai E:{'%+06.1f' % menu.input}
|
|
input: 0
|
|
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
input_step: 1.0
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
M83
|
|
G1 E{menu.input} F240
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
### menu move 0.1mm ###
|
|
[menu __main __control __move_01mm]
|
|
type: list
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Verplaats 0.1mm
|
|
|
|
[menu __main __control __move_01mm __axis_x]
|
|
type: input
|
|
name: Verplaats X:{'%05.1f' % menu.input}
|
|
input: {printer.gcode_move.gcode_position.x}
|
|
input_min: {printer.toolhead.axis_minimum.x}
|
|
input_max: {printer.toolhead.axis_maximum.x}
|
|
input_step: 0.1
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
G90
|
|
G1 X{menu.input}
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
[menu __main __control __move_01mm __axis_y]
|
|
type: input
|
|
name: Verplaats Y:{'%05.1f' % menu.input}
|
|
input: {printer.gcode_move.gcode_position.y}
|
|
input_min: {printer.toolhead.axis_minimum.y}
|
|
input_max: {printer.toolhead.axis_maximum.y}
|
|
input_step: 0.1
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
G90
|
|
G1 Y{menu.input}
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
[menu __main __control __move_01mm __axis_z]
|
|
type: input
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Verplaats Z:{'%05.1f' % menu.input}
|
|
input: {printer.gcode_move.gcode_position.z}
|
|
input_min: 0
|
|
input_max: {printer.toolhead.axis_maximum.z}
|
|
input_step: 0.1
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
G90
|
|
G1 Z{menu.input}
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
[menu __main __control __move_01mm __axis_e]
|
|
type: input
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Draai E:{'%+06.1f' % menu.input}
|
|
input: 0
|
|
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
input_step: 0.1
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__move__axis
|
|
M83
|
|
G1 E{menu.input} F240
|
|
RESTORE_GCODE_STATE NAME=__move__axis
|
|
|
|
### menu temperature ###
|
|
[menu __main __temp]
|
|
type: list
|
|
name: Temperatuur
|
|
|
|
[menu __main __temp __hotend0_target]
|
|
type: input
|
|
enable: {('extruder' in printer) and ('extruder' in printer.heaters.available_heaters)}
|
|
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
|
input: {printer.extruder.target}
|
|
input_min: 0
|
|
input_max: {printer.configfile.config.extruder.max_temp}
|
|
input_step: 1
|
|
gcode: M104 T0 S{'%.0f' % menu.input}
|
|
|
|
[menu __main __temp __hotend1_target]
|
|
type: input
|
|
enable: {('extruder1' in printer) and ('extruder1' in printer.heaters.available_heaters)}
|
|
name: {"Ex1:%3.0f (%4.0f)" % (menu.input, printer.extruder1.temperature)}
|
|
input: {printer.extruder1.target}
|
|
input_min: 0
|
|
input_max: {printer.configfile.config.extruder1.max_temp}
|
|
input_step: 1
|
|
gcode: M104 T1 S{'%.0f' % menu.input}
|
|
|
|
[menu __main __temp __hotbed_target]
|
|
type: input
|
|
enable: {'heater_bed' in printer}
|
|
name: {"Bed:%3.0f (%4.0f)" % (menu.input, printer.heater_bed.temperature)}
|
|
input: {printer.heater_bed.target}
|
|
input_min: 0
|
|
input_max: {printer.configfile.config.heater_bed.max_temp}
|
|
input_step: 1
|
|
gcode: M140 S{'%.0f' % menu.input}
|
|
|
|
[menu __main __temp __preheat_pla]
|
|
type: list
|
|
name: Voorverwarmen PLA
|
|
|
|
[menu __main __temp __preheat_pla __all]
|
|
type: command
|
|
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
|
name: Alles voorverwarmen
|
|
gcode:
|
|
M140 S60
|
|
M104 S200
|
|
|
|
[menu __main __temp __preheat_pla __hotend]
|
|
type: command
|
|
enable: {'extruder' in printer}
|
|
name: Hotend voorverwarmen
|
|
gcode: M104 S200
|
|
|
|
[menu __main __temp __preheat_pla __hotbed]
|
|
type: command
|
|
enable: {'heater_bed' in printer}
|
|
name: Hotbed voorverwarmen
|
|
gcode: M140 S60
|
|
|
|
[menu __main __temp __preheat_abs]
|
|
type: list
|
|
name: Voorverwarmen ABS
|
|
|
|
[menu __main __temp __preheat_abs __all]
|
|
type: command
|
|
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
|
name: Alles voorverwarmen
|
|
gcode:
|
|
M140 S110
|
|
M104 S245
|
|
|
|
[menu __main __temp __preheat_abs __hotend]
|
|
type: command
|
|
enable: {'extruder' in printer}
|
|
name: Hotend voorverwarmen
|
|
gcode: M104 S245
|
|
|
|
[menu __main __temp __preheat_abs __hotbed]
|
|
type: command
|
|
enable: {'heater_bed' in printer}
|
|
name: Hotbed voorverwarmen
|
|
gcode: M140 S110
|
|
|
|
[menu __main __temp __cooldown]
|
|
type: list
|
|
name: Afkoelen
|
|
|
|
[menu __main __temp __cooldown __all]
|
|
type: command
|
|
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
|
name: Alles afkoelen
|
|
gcode:
|
|
M104 S0
|
|
M140 S0
|
|
|
|
[menu __main __temp __cooldown __hotend]
|
|
type: command
|
|
enable: {'extruder' in printer}
|
|
name: Hotend afkoelen
|
|
gcode: M104 S0
|
|
|
|
[menu __main __temp __cooldown __hotbed]
|
|
type: command
|
|
enable: {'heater_bed' in printer}
|
|
name: Hotbed afkoelen
|
|
gcode: M140 S0
|
|
|
|
### menu filament ###
|
|
|
|
[menu __main __filament]
|
|
type: list
|
|
name: Filament
|
|
|
|
[menu __main __filament __hotend0_target]
|
|
type: input
|
|
enable: {'extruder' in printer}
|
|
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
|
input: {printer.extruder.target}
|
|
input_min: 0
|
|
input_max: {printer.configfile.config.extruder.max_temp}
|
|
input_step: 1
|
|
gcode: M104 T0 S{'%.0f' % menu.input}
|
|
|
|
[menu __main __filament __loadf]
|
|
type: command
|
|
name: Fil. snel laden
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__filament__load
|
|
M83
|
|
G1 E50 F960
|
|
RESTORE_GCODE_STATE NAME=__filament__load
|
|
|
|
[menu __main __filament __loads]
|
|
type: command
|
|
name: Fil. langzaam laden
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__filament__load
|
|
M83
|
|
G1 E50 F240
|
|
RESTORE_GCODE_STATE NAME=__filament__load
|
|
|
|
[menu __main __filament __unloadf]
|
|
type: command
|
|
name: Fil. snel uitwerpen
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__filament__load
|
|
M83
|
|
G1 E-50 F960
|
|
RESTORE_GCODE_STATE NAME=__filament__load
|
|
|
|
[menu __main __filament __unloads]
|
|
type: command
|
|
name: Fil. langzaam uitwerpen
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__filament__load
|
|
M83
|
|
G1 E-50 F240
|
|
RESTORE_GCODE_STATE NAME=__filament__load
|
|
|
|
[menu __main __filament __feed]
|
|
type: input
|
|
name: Snelheid: {'%.1f' % menu.input}
|
|
input: 5
|
|
input_step: 0.1
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=__filament__load
|
|
M83
|
|
G1 E{'%.1f' % menu.input} F60
|
|
RESTORE_GCODE_STATE NAME=__filament__load
|
|
|
|
### menu setup ###
|
|
[menu __main __setup]
|
|
type: list
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Setup
|
|
|
|
[menu __main __setup __save_config]
|
|
type: command
|
|
name: Bewaar configuratie
|
|
gcode: SAVE_CONFIG
|
|
|
|
[menu __main __setup __restart]
|
|
type: list
|
|
name: Herstarten
|
|
|
|
[menu __main __setup __restart __host_restart]
|
|
type: command
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Herstart host
|
|
gcode: RESTART
|
|
|
|
[menu __main __setup __restart __firmware_restart]
|
|
type: command
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Herstart FW
|
|
gcode: FIRMWARE_RESTART
|
|
|
|
[menu __main __setup __tuning]
|
|
type: list
|
|
name: PID tuning
|
|
|
|
[menu __main __setup __tuning __hotend_pid_tuning]
|
|
type: command
|
|
enable: {(not printer.idle_timeout.state == "Printing") and ('extruder' in printer)}
|
|
name: Tune Hotend PID
|
|
gcode: PID_CALIBRATE HEATER=extruder TARGET=210 WRITE_FILE=1
|
|
|
|
[menu __main __setup __tuning __hotbed_pid_tuning]
|
|
type: command
|
|
enable: {(not printer.idle_timeout.state == "Printing") and ('heater_bed' in printer)}
|
|
name: Tune Hotbed PID
|
|
gcode: PID_CALIBRATE HEATER=heater_bed TARGET=60 WRITE_FILE=1
|
|
|
|
[menu __main __setup __calib]
|
|
type: list
|
|
name: Calibratie
|
|
|
|
[menu __main __setup __calib __bedprobe]
|
|
type: command
|
|
enable: {not printer.idle_timeout.state == "Printing"}
|
|
name: Bed probe
|
|
gcode: PROBE
|
|
|
|
[menu __main __setup __dump]
|
|
type: command
|
|
name: Dump parameters
|
|
gcode:
|
|
{% for name1 in printer %}
|
|
{% for name2 in printer[name1] %}
|
|
{ action_respond_info("printer['%s'].%s = %s"
|
|
% (name1, name2, printer[name1][name2])) }
|
|
{% else %}
|
|
{ action_respond_info("printer['%s'] = %s" % (name1, printer[name1])) }
|
|
{% endfor %}
|
|
{% endfor %}
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 30.552
|
|
#*# pid_ki = 2.289
|
|
#*# pid_kd = 101.966
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 69.576
|
|
#*# pid_ki = 0.488
|
|
#*# pid_kd = 2478.635
|
|
#*#
|
|
#*# [bltouch]
|
|
#*# z_offset = 2.920
|
|
#*#
|
|
#*# [stepper_z]
|
|
#*#
|
|
#*# [bed_mesh GlasbedCarbonBoven]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.250000, 0.085000, 0.025000, -0.015000, -0.027500
|
|
#*# 0.192500, 0.072500, 0.015000, -0.015000, -0.045000
|
|
#*# 0.052500, -0.032500, -0.037500, -0.050000, 0.015000
|
|
#*# -0.030000, -0.017500, 0.025000, 0.072500, 0.117500
|
|
#*# 0.032500, 0.005000, 0.042500, 0.032500, 0.127500
|
|
#*# tension = 0.2
|
|
#*# min_x = 25.0
|
|
#*# algo = lagrange
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 10.0
|
|
#*# x_count = 5
|
|
#*# max_y = 170.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 200.0
|
|
#*#
|
|
#*# [bed_mesh GlasbedCarbonBoven ]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.030000, -0.065000, -0.075000, -0.145000, -0.165000
|
|
#*# 0.272500, 0.092500, -0.070000, -0.275000, -0.422500
|
|
#*# 0.027500, -0.052500, -0.075000, -0.165000, -0.160000
|
|
#*# -0.045000, -0.040000, -0.045000, -0.105000, -0.057500
|
|
#*# 0.017500, 0.005000, 0.022500, -0.012500, 0.002500
|
|
#*# tension = 0.2
|
|
#*# min_x = 25.0
|
|
#*# algo = lagrange
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 10.0
|
|
#*# x_count = 5
|
|
#*# max_y = 170.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 200.0
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# -0.487500, -0.502500, -0.547500, -0.582500, -0.582500
|
|
#*# -0.545000, -0.515000, -0.542500, -0.585000, -0.570000
|
|
#*# -0.692500, -0.587500, -0.587500, -0.570000, -0.490000
|
|
#*# -0.785000, -0.630000, -0.585000, -0.540000, -0.400000
|
|
#*# -0.710000, -0.582500, -0.575000, -0.545000, -0.407500
|
|
#*# tension = 0.2
|
|
#*# min_x = 25.0
|
|
#*# algo = lagrange
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 10.0
|
|
#*# x_count = 5
|
|
#*# max_y = 170.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 200.0
|