126 lines
4.2 KiB
INI
126 lines
4.2 KiB
INI
[pause_resume]
|
|
|
|
[gcode_macro PAUSE]
|
|
description: Pause the actual running print
|
|
rename_existing: PAUSE_BASE
|
|
# change this if you need more or less extrusion
|
|
variable_extrude: 1.0
|
|
gcode:
|
|
##### read E from pause macro #####
|
|
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
|
##### set park positon for x and y #####
|
|
# default is your max posion from your printer.cfg
|
|
{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
|
|
{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
|
|
##### calculate save lift position #####
|
|
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
|
{% set act_z = printer.toolhead.position.z|float %}
|
|
{% if act_z < (max_z - 2.0) %}
|
|
{% set z_safe = 2.0 %}
|
|
{% else %}
|
|
{% set z_safe = max_z - act_z %}
|
|
{% endif %}
|
|
##### end of definitions #####
|
|
PAUSE_BASE
|
|
G91
|
|
{% if printer.extruder.can_extrude|lower == 'true' %}
|
|
G1 E-{E} F2100
|
|
{% else %}
|
|
{action_respond_info("Extruder not hot enough")}
|
|
{% endif %}
|
|
{% if "xyz" in printer.toolhead.homed_axes %}
|
|
G1 Z{z_safe} F900
|
|
G90
|
|
G1 X{x_park} Y{y_park} F6000
|
|
{% else %}
|
|
{action_respond_info("Printer not homed")}
|
|
{% endif %}
|
|
|
|
[gcode_macro RESUME]
|
|
description: Resume the actual running print
|
|
rename_existing: RESUME_BASE
|
|
gcode:
|
|
##### read E from pause macro #####
|
|
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
|
#### get VELOCITY parameter if specified ####
|
|
{% if 'VELOCITY' in params|upper %}
|
|
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
|
{%else %}
|
|
{% set get_params = "" %}
|
|
{% endif %}
|
|
##### end of definitions #####
|
|
{% if printer.extruder.can_extrude|lower == 'true' %}
|
|
G91
|
|
G1 E{E} F2100
|
|
{% else %}
|
|
{action_respond_info("Extruder not hot enough")}
|
|
{% endif %}
|
|
RESUME_BASE {get_params}
|
|
|
|
[gcode_macro CANCEL_PRINT]
|
|
description: Cancel the actual running print
|
|
rename_existing: CANCEL_PRINT_BASE
|
|
gcode:
|
|
TURN_OFF_HEATERS
|
|
CANCEL_PRINT_BASE
|
|
|
|
# The print bed can move so far to the front, that the nozzle can reach the
|
|
# plastic cover of the print bed heater cable (only when the bed is moved by
|
|
# hand). By homing the Y axis before the X axis, it is ensured the nozzle will
|
|
# not melt through the plastic part.
|
|
# BEWARE: You will lose the ability to home axes individually. The printer will
|
|
# always home all axes for every G28 command.
|
|
#[homing_override]
|
|
#gcode:
|
|
# G28 Y0
|
|
# G28 X0
|
|
# G28 Z0
|
|
|
|
# ================================================================================
|
|
# GCode Macro: START_PRINT
|
|
# Add START_PRINT in your slicers starting script.
|
|
# ================================================================================
|
|
[gcode_macro START_PRINT]
|
|
gcode:
|
|
G28; Home all axes
|
|
BED_MESH_CALIBRATE
|
|
G92 E0; Reset Extruder
|
|
G1 Z25.0 F3000; Move Z Axis up little to prevent scratching of Heat Bed
|
|
G1 X0.1 Y20 Z0.3 F5000.0; Move to start position
|
|
G1 X0.1 Y200.0 Z0.3 F1500.0 E15; Draw the first line
|
|
G1 X0.4 Y200.0 Z0.3 F5000.0; Move to side a little
|
|
G1 X0.4 Y20 Z0.3 F1500.0 E30; Draw the second line
|
|
G92 E0; Reset Extruder
|
|
G1 Z25.0 F3000; Move Z Axis up little to prevent scratching of Heat Bed
|
|
M118 punt gcode_macro START_PRINT
|
|
|
|
# ================================================================================
|
|
# GCode Macro: END_PRINT
|
|
# Add END_PRINT in your slicers ending script
|
|
# ================================================================================
|
|
[gcode_macro END_PRINT]
|
|
gcode:
|
|
G91; Relative Positioning
|
|
G1 Z+10; Move Z up so it doesn't hit anything
|
|
G90; Absolute Positioning
|
|
G1 Y190 F1500; bring Y up front
|
|
# G10 ; set tool offset? or retract?
|
|
# G1 E-10 F300; Retrack-10
|
|
G1 X10 Y220 F2000; Move to X10, Y220
|
|
M104 S0; Turn off Extruder temperature (set it to 0)
|
|
M140 S0; Turn off Bed temperature (set it to 0)
|
|
M106 S0; turn off cooling fan
|
|
M84; Disable steppers
|
|
# ================================================================================
|
|
# GCode Macro G29
|
|
# Fires when G29 is sent to the printer
|
|
# ================================================================================
|
|
#[gcode_macro G29]
|
|
#gcode:
|
|
# G1 Z10 F600
|
|
# G4 P200
|
|
# G1 Z10 F600
|
|
# G4 P100
|
|
|
|
### Raspberry Pi als MCU om de GPIO te gebruiken voor in- en output
|