[bed_mesh]
speed: 100
horizontal_move_z: 5
mesh_min: 5,5
mesh_max: 220,195
algorithm: bicubic
bicubic_tension: 0.1
probe_count: 7,7
mesh_pps: 2,2
relative_reference_index: 24   # (5,3)=7 (3,3)=4 (5,5)=12 (7,7)=24 (7,5)=17 (9,9)=40
move_check_distance: 5.0
split_delta_z: .025
fade_start: 0.6
fade_end: 10
fade_target: 0

[gcode_macro BED_MESH_CALIBRATE]
rename_existing: BED_MESH_CALIBRATE_BASE
variable_mesh_delta : 25                   ## distance between points
variable_x_mesh_max : 7                    ## max points on x-axis
variable_y_mesh_max : 7                    ## max points on y-axis
variable_mesh_area_offset : 5              ## the clearance between print area and probe area
gcode=
	{% if params.AREA_START and params.AREA_END %}
	## get [bed_mesh] config parameters
		{% set bedMeshConfig = printer["configfile"].config["bed_mesh"] %}
		{% set safe_min_x = bedMeshConfig.mesh_min.split(",")[0]|float %}
		{% set safe_min_y = bedMeshConfig.mesh_min.split(",")[1]|float %}
		{% set safe_max_x = bedMeshConfig.mesh_max.split(",")[0]|float %}
		{% set safe_max_y = bedMeshConfig.mesh_max.split(",")[1]|float %}
	## get print area min/max from slicer gcode
		{% set area_min_x = params.AREA_START.split(",")[0]|float %}
		{% set area_min_y = params.AREA_START.split(",")[1]|float %}
		{% set area_max_x = params.AREA_END.split(",")[0]|float %}
		{% set area_max_y = params.AREA_END.split(",")[1]|float %}
	## set probing area
		{% if area_min_x - mesh_area_offset >=  safe_min_x %}
			{% set area_min_x = area_min_x - mesh_area_offset %}
			{% else %}
			{% set area_min_x = safe_min_x %}
			{% endif %}
		{% if area_min_y - mesh_area_offset >=  safe_min_y %}
			{% set area_min_y = area_min_y - mesh_area_offset %}
			{% else %}
			{% set area_min_y = safe_min_y %}
			{% endif %}
		{% if area_max_x + mesh_area_offset <=  safe_max_x %}
			{% set area_max_x = area_max_x + mesh_area_offset %}
			{% else %}
			{% set area_max_x = safe_max_x %}
			{% endif %}
		{% if area_max_y + mesh_area_offset <=  safe_max_y %}
			{% set area_max_y = area_max_y + mesh_area_offset %}
			{% else %}
			{% set area_max_y = safe_max_y %}
			{% endif %}
	## set probe counts
		{% set meshPointX = ((area_max_x - area_min_x) / mesh_delta + 1)|round(0)|int %}
		{% if meshPointX < 3 %}
			{% set meshPointX = 3 %}
			{% elif meshPointX > x_mesh_max %}
			{% set meshPointX = x_mesh_max %}
			{% endif %}
		{% set meshPointY = ((area_max_y - area_min_y) / mesh_delta + 1)|round(0)|int %}
		{% if meshPointY < 3 %}
			{% set meshPointY = 3 %}
			{% elif meshPointY > y_mesh_max %}
			{% set meshPointY = y_mesh_max %}
			{% endif %}
	## check for invalid mesh
		{% if meshPointX > 5 %}
			{% if meshPointY == 3 %}  # 7x3 mesh invlaid for bicubic
			{% set meshPointY = 5 %}  # set 7x5 mesh
			{% endif %}
			{% endif %}
		{% if meshPointY > 5 %}
			{% if meshPointX == 3 %}  # 3x7 mesh invlaid for bicubic
			{% set meshPointX = 5 %}  # set 5x7 mesh
			{% endif %}
			{% endif %}
	## set new reference index point
		{% set referenceIndex = (meshPointX * meshPointY / 2 - 1 )|round(0)|int %}
	## send bed mesh parameters
		M117 probe_count={meshPointX},{meshPointY}
		BED_MESH_CALIBRATE_BASE mesh_min={area_min_x},{area_min_y} mesh_max={area_max_x},{area_max_y} probe_count={meshPointX},{meshPointY} relative_reference_index={referenceIndex} 
	{% else %}
	BED_MESH_CALIBRATE_BASE
	{% endif %}