Upload files to "klipper/DNV-TPU-Ender3/klipper_config"
This commit is contained in:
@@ -0,0 +1,907 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
||||
# E3 v1.2. To use this config, the firmware should be compiled for the
|
||||
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
||||
# select "Enable extra low-level configuration options" and configure
|
||||
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
||||
|
||||
# The "make flash" command does not work on the SKR mini E3. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the SKR
|
||||
# mini E3 with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# Note: This board has a design flaw in its thermistor circuits that
|
||||
# cause inaccurate temperatures (most noticeable at low temperatures).
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB13
|
||||
dir_pin: !PB12
|
||||
enable_pin: !PB14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC0
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PB15
|
||||
run_current: 0.580
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB10
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PB11
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC1
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC6
|
||||
run_current: 0.580
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB0
|
||||
dir_pin: PC5
|
||||
enable_pin: !PB1
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0.0
|
||||
position_max: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC10
|
||||
run_current: 0.580
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC14 ;mine uses the Z pin for sensor
|
||||
control_pin: PA1
|
||||
pin_up_reports_not_triggered: False
|
||||
pin_up_touch_mode_reports_triggered: False
|
||||
x_offset: 32.4
|
||||
y_offset: -34.9
|
||||
z_offset: 1.6
|
||||
pin_move_time: 1.5
|
||||
|
||||
[extruder]
|
||||
# DropEffect OmniaDrop V2.1
|
||||
step_pin: PB3
|
||||
dir_pin: !PB4
|
||||
enable_pin: !PD2
|
||||
microsteps: 16
|
||||
gear_ratio: 5:1
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC8
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA0
|
||||
control: pid
|
||||
pid_Kp: 21.527
|
||||
pid_Ki: 1.063
|
||||
pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC11
|
||||
run_current: 0.500
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PC9
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC3
|
||||
control: pid
|
||||
pid_Kp: 54.027
|
||||
pid_Ki: 0.770
|
||||
pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA8
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[static_digital_output usb_pullup_enable]
|
||||
pins: !PC13
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: EXP1_7
|
||||
sclk_pin: EXP1_6
|
||||
sid_pin: EXP1_8
|
||||
encoder_pins: ^EXP1_5, ^EXP1_3
|
||||
click_pin: ^!EXP1_2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
[virtual_sdcard]
|
||||
path: ~/gcode_files
|
||||
|
||||
[display_status]
|
||||
|
||||
[pause_resume]
|
||||
|
||||
[gcode_macro PAUSE]
|
||||
description: Pause the actual running print
|
||||
rename_existing: PAUSE_BASE
|
||||
# change this if you need more or less extrusion
|
||||
variable_extrude: 1.0
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
##### set park positon for x and y #####
|
||||
# default is your max posion from your printer.cfg
|
||||
{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
|
||||
{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
|
||||
##### calculate save lift position #####
|
||||
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
||||
{% set act_z = printer.toolhead.position.z|float %}
|
||||
{% if act_z < (max_z - 2.0) %}
|
||||
{% set z_safe = 2.0 %}
|
||||
{% else %}
|
||||
{% set z_safe = max_z - act_z %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
PAUSE_BASE
|
||||
G91
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G1 E-{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
{% if "xyz" in printer.toolhead.homed_axes %}
|
||||
G1 Z{z_safe} F900
|
||||
G90
|
||||
G1 X{x_park} Y{y_park} F6000
|
||||
{% else %}
|
||||
{action_respond_info("Printer not homed")}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro RESUME]
|
||||
description: Resume the actual running print
|
||||
rename_existing: RESUME_BASE
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
#### get VELOCITY parameter if specified ####
|
||||
{% if 'VELOCITY' in params|upper %}
|
||||
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
||||
{%else %}
|
||||
{% set get_params = "" %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G91
|
||||
G1 E{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
RESUME_BASE {get_params}
|
||||
|
||||
[gcode_macro CANCEL_PRINT]
|
||||
description: Cancel the actual running print
|
||||
rename_existing: CANCEL_PRINT_BASE
|
||||
gcode:
|
||||
TURN_OFF_HEATERS
|
||||
CANCEL_PRINT_BASE
|
||||
|
||||
# The print bed can move so far to the front, that the nozzle can reach the
|
||||
# plastic cover of the print bed heater cable (only when the bed is moved by
|
||||
# hand). By homing the Y axis before the X axis, it is ensured the nozzle will
|
||||
# not melt through the plastic part.
|
||||
# BEWARE: You will lose the ability to home axes individually. The printer will
|
||||
# always home all axes for every G28 command.
|
||||
#[homing_override]
|
||||
#gcode:
|
||||
# G28 Y0
|
||||
# G28 X0
|
||||
# G28 Z0
|
||||
|
||||
[bed_screws]
|
||||
screw1: 32,32
|
||||
screw2: 203,32
|
||||
screw3: 203,203
|
||||
screw4: 32,203
|
||||
screw5: 117,117
|
||||
|
||||
### menu main ###
|
||||
[menu __main]
|
||||
type: list
|
||||
name: Main
|
||||
|
||||
### menu tune ###
|
||||
[menu __main __tune]
|
||||
type: list
|
||||
enable: {printer.idle_timeout.state == "Printing"}
|
||||
name: Tune
|
||||
|
||||
[menu __main __tune __speed]
|
||||
type: input
|
||||
name: Speed: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.gcode_move.speed_factor}
|
||||
input_min: 0.01
|
||||
input_max: 5
|
||||
input_step: 0.01
|
||||
realtime: True
|
||||
gcode:
|
||||
M220 S{'%d' % (menu.input*100)}
|
||||
|
||||
[menu __main __tune __flow]
|
||||
type: input
|
||||
name: Flow: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.gcode_move.extrude_factor}
|
||||
input_min: 0.01
|
||||
input_max: 2
|
||||
input_step: 0.01
|
||||
realtime: True
|
||||
gcode:
|
||||
M221 S{'%d' % (menu.input*100)}
|
||||
|
||||
[menu __main __tune __offsetz]
|
||||
type: input
|
||||
name: Offset Z:{'%05.3f' % menu.input}
|
||||
input: {printer.gcode_move.homing_origin.z}
|
||||
input_min: -5
|
||||
input_max: 5
|
||||
input_step: 0.005
|
||||
realtime: True
|
||||
gcode:
|
||||
SET_GCODE_OFFSET Z={'%.3f' % menu.input} MOVE=1
|
||||
|
||||
|
||||
### menu octoprint ###
|
||||
[menu __main __octoprint]
|
||||
type: list
|
||||
name: OctoPrint
|
||||
|
||||
[menu __main __octoprint __pause]
|
||||
type: command
|
||||
enable: {printer.idle_timeout.state == "Printing"}
|
||||
name: Pause printing
|
||||
gcode:
|
||||
{action_respond_info('action:pause')}
|
||||
|
||||
[menu __main __octoprint __resume]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Resume printing
|
||||
gcode:
|
||||
{action_respond_info('action:resume')}
|
||||
|
||||
[menu __main __octoprint __abort]
|
||||
type: command
|
||||
enable: {printer.idle_timeout.state == "Printing"}
|
||||
name: Abort printing
|
||||
gcode:
|
||||
{action_respond_info('action:cancel')}
|
||||
|
||||
### menu virtual sdcard ###
|
||||
[menu __main __sdcard]
|
||||
type: vsdlist
|
||||
enable: {('virtual_sdcard' in printer)}
|
||||
name: SD Card
|
||||
|
||||
[menu __main __sdcard __start]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.virtual_sdcard.file_path and not printer.virtual_sdcard.is_active}
|
||||
name: Start printing
|
||||
gcode: M24
|
||||
|
||||
[menu __main __sdcard __resume]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "paused"}
|
||||
name: Resume printing
|
||||
gcode:
|
||||
{% if "pause_resume" in printer %}
|
||||
RESUME
|
||||
{% else %}
|
||||
M24
|
||||
{% endif %}
|
||||
|
||||
[menu __main __sdcard __pause]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "printing"}
|
||||
name: Pause printing
|
||||
gcode:
|
||||
{% if "pause_resume" in printer %}
|
||||
PAUSE
|
||||
{% else %}
|
||||
M25
|
||||
{% endif %}
|
||||
|
||||
[menu __main __sdcard __cancel]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and (printer.print_stats.state == "printing" or printer.print_stats.state == "paused")}
|
||||
name: Cancel printing
|
||||
gcode:
|
||||
{% if 'pause_resume' in printer %}
|
||||
CANCEL_PRINT
|
||||
{% else %}
|
||||
M25
|
||||
M27
|
||||
M26 S0
|
||||
TURN_OFF_HEATERS
|
||||
{% if printer.toolhead.position.z <= printer.toolhead.axis_maximum.z - 5 %}
|
||||
G91
|
||||
G0 Z5 F1000
|
||||
G90
|
||||
{% endif %}
|
||||
{% endif %}
|
||||
|
||||
### menu control ###
|
||||
[menu __main __control]
|
||||
type: list
|
||||
name: Control
|
||||
|
||||
[menu __main __control __home]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home All
|
||||
gcode: G28
|
||||
|
||||
[menu __main __control __homez]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home Z
|
||||
gcode: G28 Z
|
||||
|
||||
[menu __main __control __homexy]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home X/Y
|
||||
gcode: G28 X Y
|
||||
|
||||
[menu __main __control __disable]
|
||||
type: command
|
||||
name: Steppers off
|
||||
gcode:
|
||||
M84
|
||||
M18
|
||||
|
||||
[menu __main __control __fanonoff]
|
||||
type: input
|
||||
enable: {'fan' in printer}
|
||||
name: Fan: {'ON ' if menu.input else 'OFF'}
|
||||
input: {printer.fan.speed}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 1
|
||||
gcode:
|
||||
M106 S{255 if menu.input else 0}
|
||||
|
||||
[menu __main __control __fanspeed]
|
||||
type: input
|
||||
enable: {'fan' in printer}
|
||||
name: Fan speed: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.fan.speed}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 0.01
|
||||
gcode:
|
||||
M106 S{'%d' % (menu.input*255)}
|
||||
|
||||
[menu __main __control __caselightonoff]
|
||||
type: input
|
||||
enable: {'output_pin caselight' in printer}
|
||||
name: Lights: {'ON ' if menu.input else 'OFF'}
|
||||
input: {printer['output_pin caselight'].value}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 1
|
||||
gcode:
|
||||
SET_PIN PIN=caselight VALUE={1 if menu.input else 0}
|
||||
|
||||
[menu __main __control __caselightpwm]
|
||||
type: input
|
||||
enable: {'output_pin caselight' in printer}
|
||||
name: Lights: {'%3d' % (menu.input*100)}%
|
||||
input: {printer['output_pin caselight'].value}
|
||||
input_min: 0.0
|
||||
input_max: 1.0
|
||||
input_step: 0.01
|
||||
gcode:
|
||||
SET_PIN PIN=caselight VALUE={menu.input}
|
||||
|
||||
### menu move 10mm ###
|
||||
[menu __main __control __move_10mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move 10mm
|
||||
|
||||
[menu __main __control __move_10mm __axis_x]
|
||||
type: input
|
||||
name: Move X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_y]
|
||||
type: input
|
||||
name: Move Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 1mm ###
|
||||
[menu __main __control __move_1mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move 1mm
|
||||
|
||||
[menu __main __control __move_1mm __axis_x]
|
||||
type: input
|
||||
name: Move X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_y]
|
||||
type: input
|
||||
name: Move Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 0.1mm ###
|
||||
[menu __main __control __move_01mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move 0.1mm
|
||||
|
||||
[menu __main __control __move_01mm __axis_x]
|
||||
type: input
|
||||
name: Move X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_y]
|
||||
type: input
|
||||
name: Move Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Move E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu temperature ###
|
||||
[menu __main __temp]
|
||||
type: list
|
||||
name: Temperature
|
||||
|
||||
[menu __main __temp __hotend0_target]
|
||||
type: input
|
||||
enable: {('extruder' in printer) and ('extruder' in printer.heaters.available_heaters)}
|
||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
||||
input: {printer.extruder.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __hotend1_target]
|
||||
type: input
|
||||
enable: {('extruder1' in printer) and ('extruder1' in printer.heaters.available_heaters)}
|
||||
name: {"Ex1:%3.0f (%4.0f)" % (menu.input, printer.extruder1.temperature)}
|
||||
input: {printer.extruder1.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder1.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T1 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __hotbed_target]
|
||||
type: input
|
||||
enable: {'heater_bed' in printer}
|
||||
name: {"Bed:%3.0f (%4.0f)" % (menu.input, printer.heater_bed.temperature)}
|
||||
input: {printer.heater_bed.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.heater_bed.max_temp}
|
||||
input_step: 1
|
||||
gcode: M140 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __preheat_pla]
|
||||
type: list
|
||||
name: Preheat PLA
|
||||
|
||||
[menu __main __temp __preheat_pla __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Preheat all
|
||||
gcode:
|
||||
M140 S60
|
||||
M104 S200
|
||||
|
||||
[menu __main __temp __preheat_pla __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Preheat hotend
|
||||
gcode: M104 S200
|
||||
|
||||
[menu __main __temp __preheat_pla __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Preheat hotbed
|
||||
gcode: M140 S60
|
||||
|
||||
[menu __main __temp __preheat_abs]
|
||||
type: list
|
||||
name: Preheat ABS
|
||||
|
||||
[menu __main __temp __preheat_abs __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Preheat all
|
||||
gcode:
|
||||
M140 S110
|
||||
M104 S245
|
||||
|
||||
[menu __main __temp __preheat_abs __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Preheat hotend
|
||||
gcode: M104 S245
|
||||
|
||||
[menu __main __temp __preheat_abs __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Preheat hotbed
|
||||
gcode: M140 S110
|
||||
|
||||
[menu __main __temp __cooldown]
|
||||
type: list
|
||||
name: Cooldown
|
||||
|
||||
[menu __main __temp __cooldown __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Cooldown all
|
||||
gcode:
|
||||
M104 S0
|
||||
M140 S0
|
||||
|
||||
[menu __main __temp __cooldown __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Cooldown hotend
|
||||
gcode: M104 S0
|
||||
|
||||
[menu __main __temp __cooldown __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Cooldown hotbed
|
||||
gcode: M140 S0
|
||||
|
||||
### menu filament ###
|
||||
|
||||
[menu __main __filament]
|
||||
type: list
|
||||
name: Filament
|
||||
|
||||
[menu __main __filament __hotend0_target]
|
||||
type: input
|
||||
enable: {'extruder' in printer}
|
||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
||||
input: {printer.extruder.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __filament __loadf]
|
||||
type: command
|
||||
name: Load Fil. fast
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E50 F960
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __loads]
|
||||
type: command
|
||||
name: Load Fil. slow
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E50 F240
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __unloadf]
|
||||
type: command
|
||||
name: Unload Fil.fast
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E-50 F960
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __unloads]
|
||||
type: command
|
||||
name: Unload Fil.slow
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E-50 F240
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __feed]
|
||||
type: input
|
||||
name: Feed: {'%.1f' % menu.input}
|
||||
input: 5
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E{'%.1f' % menu.input} F60
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
### menu setup ###
|
||||
[menu __main __setup]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Setup
|
||||
|
||||
[menu __main __setup __save_config]
|
||||
type: command
|
||||
name: Save config
|
||||
gcode: SAVE_CONFIG
|
||||
|
||||
[menu __main __setup __restart]
|
||||
type: list
|
||||
name: Restart
|
||||
|
||||
[menu __main __setup __restart __host_restart]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Restart host
|
||||
gcode: RESTART
|
||||
|
||||
[menu __main __setup __restart __firmware_restart]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Restart FW
|
||||
gcode: FIRMWARE_RESTART
|
||||
|
||||
[menu __main __setup __tuning]
|
||||
type: list
|
||||
name: PID tuning
|
||||
|
||||
[menu __main __setup __tuning __hotend_pid_tuning]
|
||||
type: command
|
||||
enable: {(not printer.idle_timeout.state == "Printing") and ('extruder' in printer)}
|
||||
name: Tune Hotend PID
|
||||
gcode: PID_CALIBRATE HEATER=extruder TARGET=210 WRITE_FILE=1
|
||||
|
||||
[menu __main __setup __tuning __hotbed_pid_tuning]
|
||||
type: command
|
||||
enable: {(not printer.idle_timeout.state == "Printing") and ('heater_bed' in printer)}
|
||||
name: Tune Hotbed PID
|
||||
gcode: PID_CALIBRATE HEATER=heater_bed TARGET=60 WRITE_FILE=1
|
||||
|
||||
[menu __main __setup __calib]
|
||||
type: list
|
||||
name: Calibration
|
||||
|
||||
[menu __main __setup __calib __delta_calib_auto]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Delta cal. auto
|
||||
gcode:
|
||||
G28
|
||||
DELTA_CALIBRATE
|
||||
|
||||
[menu __main __setup __calib __delta_calib_man]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Delta cal. man
|
||||
|
||||
[menu __main __setup __calib __bedprobe]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Bed probe
|
||||
gcode: PROBE
|
||||
|
||||
[menu __main __setup __calib __delta_calib_man __start]
|
||||
type: command
|
||||
name: Start probing
|
||||
gcode:
|
||||
G28
|
||||
DELTA_CALIBRATE METHOD=manual
|
||||
|
||||
[menu __main __setup __calib __delta_calib_man __move_z]
|
||||
type: input
|
||||
name: Move Z: {'%03.2f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_step: 1
|
||||
realtime: True
|
||||
gcode:
|
||||
{%- if menu.event == 'change' -%}
|
||||
G1 Z{'%.2f' % menu.input}
|
||||
{%- elif menu.event == 'long_click' -%}
|
||||
G1 Z{'%.2f' % menu.input}
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G91
|
||||
G1 Z2
|
||||
G1 Z-2
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
{%- endif -%}
|
||||
|
||||
[menu __main __setup __calib __delta_calib_man __test_z]
|
||||
type: input
|
||||
name: Test Z: {['++','+','+.01','+.05','+.1','+.5','-.5','-.1','-.05','-.01','-','--'][menu.input|int]}
|
||||
input: 6
|
||||
input_min: 0
|
||||
input_max: 11
|
||||
input_step: 1
|
||||
gcode:
|
||||
{%- if menu.event == 'long_click' -%}
|
||||
TESTZ Z={['++','+','+.01','+.05','+.1','+.5','-.5','-.1','-.05','-.01','-','--'][menu.input|int]}
|
||||
{%- endif -%}
|
||||
|
||||
[menu __main __setup __calib __delta_calib_man __accept]
|
||||
type: command
|
||||
name: Accept
|
||||
gcode: ACCEPT
|
||||
|
||||
[menu __main __setup __calib __delta_calib_man __abort]
|
||||
type: command
|
||||
name: Abort
|
||||
gcode: ABORT
|
||||
|
||||
[menu __main __setup __dump]
|
||||
type: command
|
||||
name: Dump parameters
|
||||
gcode:
|
||||
{% for name1 in printer %}
|
||||
{% for name2 in printer[name1] %}
|
||||
{ action_respond_info("printer['%s'].%s = %s"
|
||||
% (name1, name2, printer[name1][name2])) }
|
||||
{% else %}
|
||||
{ action_respond_info("printer['%s'] = %s" % (name1, printer[name1])) }
|
||||
{% endfor %}
|
||||
{% endfor %}
|
||||
@@ -0,0 +1,850 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
||||
# E3 v1.2. To use this config, the firmware should be compiled for the
|
||||
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
||||
# select "Enable extra low-level configuration options" and configure
|
||||
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
||||
|
||||
# The "make flash" command does not work on the SKR mini E3. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the SKR
|
||||
# mini E3 with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# Note: This board has a design flaw in its thermistor circuits that
|
||||
# cause inaccurate temperatures (most noticeable at low temperatures).
|
||||
|
||||
# Met de DropEffect OmniDrop V2.1 is het punt links-beneden (dus het 0-punt): X = 12 en Y = 30
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB13
|
||||
dir_pin: !PB12
|
||||
enable_pin: !PB14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC0
|
||||
position_endstop: -12
|
||||
position_min: -13
|
||||
position_max: 222
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PB15
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB10
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PB11
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC1
|
||||
position_endstop: -29
|
||||
position_min: -30
|
||||
position_max: 205
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC6
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB0
|
||||
dir_pin: PC5
|
||||
enable_pin: !PB1
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0.0
|
||||
position_max: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC10
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC14
|
||||
control_pin: PA1
|
||||
#pin_up_reports_not_triggered: False
|
||||
#pin_up_touch_mode_reports_triggered: False
|
||||
x_offset: 32.4
|
||||
y_offset: -34.9
|
||||
z_offset: 1.6
|
||||
pin_move_time: 0.680
|
||||
|
||||
[extruder]
|
||||
# DropEffect OmniaDrop V2.1
|
||||
step_pin: PB3
|
||||
dir_pin: PB4
|
||||
enable_pin: !PD2
|
||||
microsteps: 16
|
||||
gear_ratio: 5:1
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC8
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA0
|
||||
#control: pid
|
||||
#pid_Kp: 21.527
|
||||
#pid_Ki: 1.063
|
||||
#pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC11
|
||||
run_current: 0.500
|
||||
hold_current: 0.400
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[heater_fan my_nozzle_fan]
|
||||
# Aansturing via PT-DET pinout
|
||||
pin: PC12
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PC9
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC3
|
||||
#control: pid
|
||||
#pid_Kp: 54.027
|
||||
#pid_Ki: 0.770
|
||||
#pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA8
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[static_digital_output usb_pullup_enable]
|
||||
pins: !PC13
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: EXP1_7
|
||||
sclk_pin: EXP1_6
|
||||
sid_pin: EXP1_8
|
||||
encoder_pins: ^EXP1_5, ^EXP1_3
|
||||
click_pin: ^!EXP1_2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
[virtual_sdcard]
|
||||
path: ~/gcode_files
|
||||
|
||||
[display_status]
|
||||
|
||||
[pause_resume]
|
||||
|
||||
[gcode_macro PAUSE]
|
||||
description: Pause the actual running print
|
||||
rename_existing: PAUSE_BASE
|
||||
# change this if you need more or less extrusion
|
||||
variable_extrude: 1.0
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
##### set park positon for x and y #####
|
||||
# default is your max posion from your printer.cfg
|
||||
{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
|
||||
{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
|
||||
##### calculate save lift position #####
|
||||
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
||||
{% set act_z = printer.toolhead.position.z|float %}
|
||||
{% if act_z < (max_z - 2.0) %}
|
||||
{% set z_safe = 2.0 %}
|
||||
{% else %}
|
||||
{% set z_safe = max_z - act_z %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
PAUSE_BASE
|
||||
G91
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G1 E-{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
{% if "xyz" in printer.toolhead.homed_axes %}
|
||||
G1 Z{z_safe} F900
|
||||
G90
|
||||
G1 X{x_park} Y{y_park} F6000
|
||||
{% else %}
|
||||
{action_respond_info("Printer not homed")}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro RESUME]
|
||||
description: Resume the actual running print
|
||||
rename_existing: RESUME_BASE
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
#### get VELOCITY parameter if specified ####
|
||||
{% if 'VELOCITY' in params|upper %}
|
||||
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
||||
{%else %}
|
||||
{% set get_params = "" %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G91
|
||||
G1 E{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
RESUME_BASE {get_params}
|
||||
|
||||
[gcode_macro CANCEL_PRINT]
|
||||
description: Cancel the actual running print
|
||||
rename_existing: CANCEL_PRINT_BASE
|
||||
gcode:
|
||||
TURN_OFF_HEATERS
|
||||
CANCEL_PRINT_BASE
|
||||
|
||||
# The print bed can move so far to the front, that the nozzle can reach the
|
||||
# plastic cover of the print bed heater cable (only when the bed is moved by
|
||||
# hand). By homing the Y axis before the X axis, it is ensured the nozzle will
|
||||
# not melt through the plastic part.
|
||||
# BEWARE: You will lose the ability to home axes individually. The printer will
|
||||
# always home all axes for every G28 command.
|
||||
#[homing_override]
|
||||
#gcode:
|
||||
# G28 Y0
|
||||
# G28 X0
|
||||
# G28 Z0
|
||||
|
||||
[bed_screws]
|
||||
screw1: 32,32
|
||||
screw2: 203,32
|
||||
screw3: 203,203
|
||||
screw4: 32,203
|
||||
screw5: 117,117
|
||||
|
||||
### menu main ###
|
||||
[menu __main]
|
||||
type: list
|
||||
name: Main
|
||||
|
||||
### menu tune ###
|
||||
[menu __main __tune]
|
||||
type: list
|
||||
enable: {printer.idle_timeout.state == "Printing"}
|
||||
name: Afstellen
|
||||
|
||||
[menu __main __tune __speed]
|
||||
type: input
|
||||
name: Snelheid: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.gcode_move.speed_factor}
|
||||
input_min: 0.01
|
||||
input_max: 5
|
||||
input_step: 0.01
|
||||
realtime: True
|
||||
gcode:
|
||||
M220 S{'%d' % (menu.input*100)}
|
||||
|
||||
[menu __main __tune __flow]
|
||||
type: input
|
||||
name: Flow: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.gcode_move.extrude_factor}
|
||||
input_min: 0.01
|
||||
input_max: 2
|
||||
input_step: 0.01
|
||||
realtime: True
|
||||
gcode:
|
||||
M221 S{'%d' % (menu.input*100)}
|
||||
|
||||
[menu __main __tune __offsetz]
|
||||
type: input
|
||||
name: Offset Z:{'%05.3f' % menu.input}
|
||||
input: {printer.gcode_move.homing_origin.z}
|
||||
input_min: -5
|
||||
input_max: 5
|
||||
input_step: 0.005
|
||||
realtime: True
|
||||
gcode:
|
||||
SET_GCODE_OFFSET Z={'%.3f' % menu.input} MOVE=1
|
||||
|
||||
### menu virtual sdcard ###
|
||||
[menu __main __sdcard]
|
||||
type: vsdlist
|
||||
enable: {('virtual_sdcard' in printer)}
|
||||
name: SD Kaart
|
||||
|
||||
[menu __main __sdcard __start]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.virtual_sdcard.file_path and not printer.virtual_sdcard.is_active}
|
||||
name: Start printen
|
||||
gcode: M24
|
||||
|
||||
[menu __main __sdcard __resume]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "paused"}
|
||||
name: Herstart printen
|
||||
gcode:
|
||||
{% if "pause_resume" in printer %}
|
||||
RESUME
|
||||
{% else %}
|
||||
M24
|
||||
{% endif %}
|
||||
|
||||
[menu __main __sdcard __pause]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "printing"}
|
||||
name: Pauseer printen
|
||||
gcode:
|
||||
{% if "pause_resume" in printer %}
|
||||
PAUSE
|
||||
{% else %}
|
||||
M25
|
||||
{% endif %}
|
||||
|
||||
[menu __main __sdcard __cancel]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and (printer.print_stats.state == "printing" or printer.print_stats.state == "paused")}
|
||||
name: Annuleer printen
|
||||
gcode:
|
||||
{% if 'pause_resume' in printer %}
|
||||
CANCEL_PRINT
|
||||
{% else %}
|
||||
M25
|
||||
M27
|
||||
M26 S0
|
||||
TURN_OFF_HEATERS
|
||||
{% if printer.toolhead.position.z <= printer.toolhead.axis_maximum.z - 5 %}
|
||||
G91
|
||||
G0 Z5 F1000
|
||||
G90
|
||||
{% endif %}
|
||||
{% endif %}
|
||||
|
||||
### menu control ###
|
||||
[menu __main __control]
|
||||
type: list
|
||||
name: Control
|
||||
|
||||
[menu __main __control __home]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home All
|
||||
gcode: G28
|
||||
|
||||
[menu __main __control __homez]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home Z
|
||||
gcode: G28 Z
|
||||
|
||||
[menu __main __control __homexy]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home X/Y
|
||||
gcode: G28 X Y
|
||||
|
||||
[menu __main __control __disable]
|
||||
type: command
|
||||
name: Steppers uit
|
||||
gcode:
|
||||
M84
|
||||
M18
|
||||
|
||||
[menu __main __control __fanonoff]
|
||||
type: input
|
||||
enable: {'fan' in printer}
|
||||
name: Koeling: {'ON ' if menu.input else 'OFF'}
|
||||
input: {printer.fan.speed}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 1
|
||||
gcode:
|
||||
M106 S{255 if menu.input else 0}
|
||||
|
||||
[menu __main __control __fanspeed]
|
||||
type: input
|
||||
enable: {'fan' in printer}
|
||||
name: Snelheid koeler: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.fan.speed}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 0.01
|
||||
gcode:
|
||||
M106 S{'%d' % (menu.input*255)}
|
||||
|
||||
[menu __main __control __caselightonoff]
|
||||
type: input
|
||||
enable: {'output_pin caselight' in printer}
|
||||
name: Verlichting: {'ON ' if menu.input else 'OFF'}
|
||||
input: {printer['output_pin caselight'].value}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 1
|
||||
gcode:
|
||||
SET_PIN PIN=caselight VALUE={1 if menu.input else 0}
|
||||
|
||||
[menu __main __control __caselightpwm]
|
||||
type: input
|
||||
enable: {'output_pin caselight' in printer}
|
||||
name: Verlichting: {'%3d' % (menu.input*100)}%
|
||||
input: {printer['output_pin caselight'].value}
|
||||
input_min: 0.0
|
||||
input_max: 1.0
|
||||
input_step: 0.01
|
||||
gcode:
|
||||
SET_PIN PIN=caselight VALUE={menu.input}
|
||||
|
||||
### menu move 10mm ###
|
||||
[menu __main __control __move_10mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats 10mm
|
||||
|
||||
[menu __main __control __move_10mm __axis_x]
|
||||
type: input
|
||||
name: Verplaats X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_y]
|
||||
type: input
|
||||
name: Verplaats Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Draai E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 1mm ###
|
||||
[menu __main __control __move_1mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats 1mm
|
||||
|
||||
[menu __main __control __move_1mm __axis_x]
|
||||
type: input
|
||||
name: Verplaats X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_y]
|
||||
type: input
|
||||
name: Verplaats Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Draai E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 0.1mm ###
|
||||
[menu __main __control __move_01mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats 0.1mm
|
||||
|
||||
[menu __main __control __move_01mm __axis_x]
|
||||
type: input
|
||||
name: Verplaats X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_y]
|
||||
type: input
|
||||
name: Verplaats Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Draai E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu temperature ###
|
||||
[menu __main __temp]
|
||||
type: list
|
||||
name: Temperatuur
|
||||
|
||||
[menu __main __temp __hotend0_target]
|
||||
type: input
|
||||
enable: {('extruder' in printer) and ('extruder' in printer.heaters.available_heaters)}
|
||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
||||
input: {printer.extruder.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __hotend1_target]
|
||||
type: input
|
||||
enable: {('extruder1' in printer) and ('extruder1' in printer.heaters.available_heaters)}
|
||||
name: {"Ex1:%3.0f (%4.0f)" % (menu.input, printer.extruder1.temperature)}
|
||||
input: {printer.extruder1.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder1.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T1 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __hotbed_target]
|
||||
type: input
|
||||
enable: {'heater_bed' in printer}
|
||||
name: {"Bed:%3.0f (%4.0f)" % (menu.input, printer.heater_bed.temperature)}
|
||||
input: {printer.heater_bed.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.heater_bed.max_temp}
|
||||
input_step: 1
|
||||
gcode: M140 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __preheat_pla]
|
||||
type: list
|
||||
name: Voorverwarmen PLA
|
||||
|
||||
[menu __main __temp __preheat_pla __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Alles voorverwarmen
|
||||
gcode:
|
||||
M140 S60
|
||||
M104 S200
|
||||
|
||||
[menu __main __temp __preheat_pla __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Hotend voorverwarmen
|
||||
gcode: M104 S200
|
||||
|
||||
[menu __main __temp __preheat_pla __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Hotbed voorverwarmen
|
||||
gcode: M140 S60
|
||||
|
||||
[menu __main __temp __preheat_abs]
|
||||
type: list
|
||||
name: Voorverwarmen ABS
|
||||
|
||||
[menu __main __temp __preheat_abs __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Alles voorverwarmen
|
||||
gcode:
|
||||
M140 S110
|
||||
M104 S245
|
||||
|
||||
[menu __main __temp __preheat_abs __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Hotend voorverwarmen
|
||||
gcode: M104 S245
|
||||
|
||||
[menu __main __temp __preheat_abs __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Hotbed voorverwarmen
|
||||
gcode: M140 S110
|
||||
|
||||
[menu __main __temp __cooldown]
|
||||
type: list
|
||||
name: Afkoelen
|
||||
|
||||
[menu __main __temp __cooldown __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Alles afkoelen
|
||||
gcode:
|
||||
M104 S0
|
||||
M140 S0
|
||||
|
||||
[menu __main __temp __cooldown __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Hotend afkoelen
|
||||
gcode: M104 S0
|
||||
|
||||
[menu __main __temp __cooldown __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Hotbed afkoelen
|
||||
gcode: M140 S0
|
||||
|
||||
### menu filament ###
|
||||
|
||||
[menu __main __filament]
|
||||
type: list
|
||||
name: Filament
|
||||
|
||||
[menu __main __filament __hotend0_target]
|
||||
type: input
|
||||
enable: {'extruder' in printer}
|
||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
||||
input: {printer.extruder.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __filament __loadf]
|
||||
type: command
|
||||
name: Fil. snel laden
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E50 F960
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __loads]
|
||||
type: command
|
||||
name: Fil. langzaam laden
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E50 F240
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __unloadf]
|
||||
type: command
|
||||
name: Fil. snel uitwerpen
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E-50 F960
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __unloads]
|
||||
type: command
|
||||
name: Fil. langzaam uitwerpen
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E-50 F240
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __feed]
|
||||
type: input
|
||||
name: Snelheid: {'%.1f' % menu.input}
|
||||
input: 5
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E{'%.1f' % menu.input} F60
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
### menu setup ###
|
||||
[menu __main __setup]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Setup
|
||||
|
||||
[menu __main __setup __save_config]
|
||||
type: command
|
||||
name: Bewaar configuratie
|
||||
gcode: SAVE_CONFIG
|
||||
|
||||
[menu __main __setup __restart]
|
||||
type: list
|
||||
name: Herstarten
|
||||
|
||||
[menu __main __setup __restart __host_restart]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Herstart host
|
||||
gcode: RESTART
|
||||
|
||||
[menu __main __setup __restart __firmware_restart]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Herstart FW
|
||||
gcode: FIRMWARE_RESTART
|
||||
|
||||
[menu __main __setup __tuning]
|
||||
type: list
|
||||
name: PID tuning
|
||||
|
||||
[menu __main __setup __tuning __hotend_pid_tuning]
|
||||
type: command
|
||||
enable: {(not printer.idle_timeout.state == "Printing") and ('extruder' in printer)}
|
||||
name: Tune Hotend PID
|
||||
gcode: PID_CALIBRATE HEATER=extruder TARGET=210 WRITE_FILE=1
|
||||
|
||||
[menu __main __setup __tuning __hotbed_pid_tuning]
|
||||
type: command
|
||||
enable: {(not printer.idle_timeout.state == "Printing") and ('heater_bed' in printer)}
|
||||
name: Tune Hotbed PID
|
||||
gcode: PID_CALIBRATE HEATER=heater_bed TARGET=60 WRITE_FILE=1
|
||||
|
||||
[menu __main __setup __calib]
|
||||
type: list
|
||||
name: Calibratie
|
||||
|
||||
[menu __main __setup __calib __bedprobe]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Bed probe
|
||||
gcode: PROBE
|
||||
|
||||
[menu __main __setup __dump]
|
||||
type: command
|
||||
name: Dump parameters
|
||||
gcode:
|
||||
{% for name1 in printer %}
|
||||
{% for name2 in printer[name1] %}
|
||||
{ action_respond_info("printer['%s'].%s = %s"
|
||||
% (name1, name2, printer[name1][name2])) }
|
||||
{% else %}
|
||||
{ action_respond_info("printer['%s'] = %s" % (name1, printer[name1])) }
|
||||
{% endfor %}
|
||||
{% endfor %}
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 28.740
|
||||
#*# pid_ki = 2.129
|
||||
#*# pid_kd = 96.998
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 65.356
|
||||
#*# pid_ki = 1.168
|
||||
#*# pid_kd = 914.164
|
||||
@@ -0,0 +1,850 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
||||
# E3 v1.2. To use this config, the firmware should be compiled for the
|
||||
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
||||
# select "Enable extra low-level configuration options" and configure
|
||||
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
||||
|
||||
# The "make flash" command does not work on the SKR mini E3. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the SKR
|
||||
# mini E3 with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# Note: This board has a design flaw in its thermistor circuits that
|
||||
# cause inaccurate temperatures (most noticeable at low temperatures).
|
||||
|
||||
# Met de DropEffect OmniDrop V2.1 is het punt links-beneden (dus het 0-punt): X = 12 en Y = 30
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB13
|
||||
dir_pin: !PB12
|
||||
enable_pin: !PB14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC0
|
||||
position_endstop: -12
|
||||
position_min: -13
|
||||
position_max: 222
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PB15
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB10
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PB11
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC1
|
||||
position_endstop: -29
|
||||
position_min: -30
|
||||
position_max: 205
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC6
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB0
|
||||
dir_pin: PC5
|
||||
enable_pin: !PB1
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0.0
|
||||
position_max: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC10
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC14
|
||||
control_pin: PA1
|
||||
#pin_up_reports_not_triggered: False
|
||||
#pin_up_touch_mode_reports_triggered: False
|
||||
x_offset: 32.4
|
||||
y_offset: -34.9
|
||||
z_offset: 1.6
|
||||
pin_move_time: 0.680
|
||||
|
||||
[extruder]
|
||||
# DropEffect OmniaDrop V2.1
|
||||
step_pin: PB3
|
||||
dir_pin: PB4
|
||||
enable_pin: !PD2
|
||||
microsteps: 16
|
||||
gear_ratio: 5:1
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC8
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA0
|
||||
#control: pid
|
||||
#pid_Kp: 21.527
|
||||
#pid_Ki: 1.063
|
||||
#pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC11
|
||||
run_current: 0.500
|
||||
hold_current: 0.400
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[heater_fan my_nozzle_fan]
|
||||
# Aansturing via PT-DET pinout
|
||||
pin: PC12
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PC9
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC3
|
||||
#control: pid
|
||||
#pid_Kp: 54.027
|
||||
#pid_Ki: 0.770
|
||||
#pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA8
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[static_digital_output usb_pullup_enable]
|
||||
pins: !PC13
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: EXP1_7
|
||||
sclk_pin: EXP1_6
|
||||
sid_pin: EXP1_8
|
||||
encoder_pins: ^EXP1_5, ^EXP1_3
|
||||
click_pin: ^!EXP1_2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
[virtual_sdcard]
|
||||
path: ~/gcode_files
|
||||
|
||||
[display_status]
|
||||
|
||||
[pause_resume]
|
||||
|
||||
[gcode_macro PAUSE]
|
||||
description: Pause the actual running print
|
||||
rename_existing: PAUSE_BASE
|
||||
# change this if you need more or less extrusion
|
||||
variable_extrude: 1.0
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
##### set park positon for x and y #####
|
||||
# default is your max posion from your printer.cfg
|
||||
{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
|
||||
{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
|
||||
##### calculate save lift position #####
|
||||
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
||||
{% set act_z = printer.toolhead.position.z|float %}
|
||||
{% if act_z < (max_z - 2.0) %}
|
||||
{% set z_safe = 2.0 %}
|
||||
{% else %}
|
||||
{% set z_safe = max_z - act_z %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
PAUSE_BASE
|
||||
G91
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G1 E-{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
{% if "xyz" in printer.toolhead.homed_axes %}
|
||||
G1 Z{z_safe} F900
|
||||
G90
|
||||
G1 X{x_park} Y{y_park} F6000
|
||||
{% else %}
|
||||
{action_respond_info("Printer not homed")}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro RESUME]
|
||||
description: Resume the actual running print
|
||||
rename_existing: RESUME_BASE
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
#### get VELOCITY parameter if specified ####
|
||||
{% if 'VELOCITY' in params|upper %}
|
||||
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
||||
{%else %}
|
||||
{% set get_params = "" %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G91
|
||||
G1 E{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
RESUME_BASE {get_params}
|
||||
|
||||
[gcode_macro CANCEL_PRINT]
|
||||
description: Cancel the actual running print
|
||||
rename_existing: CANCEL_PRINT_BASE
|
||||
gcode:
|
||||
TURN_OFF_HEATERS
|
||||
CANCEL_PRINT_BASE
|
||||
|
||||
# The print bed can move so far to the front, that the nozzle can reach the
|
||||
# plastic cover of the print bed heater cable (only when the bed is moved by
|
||||
# hand). By homing the Y axis before the X axis, it is ensured the nozzle will
|
||||
# not melt through the plastic part.
|
||||
# BEWARE: You will lose the ability to home axes individually. The printer will
|
||||
# always home all axes for every G28 command.
|
||||
#[homing_override]
|
||||
#gcode:
|
||||
# G28 Y0
|
||||
# G28 X0
|
||||
# G28 Z0
|
||||
|
||||
[bed_screws]
|
||||
screw1: 32,32
|
||||
screw2: 203,32
|
||||
screw3: 203,203
|
||||
screw4: 32,203
|
||||
screw5: 117,117
|
||||
|
||||
### menu main ###
|
||||
[menu __main]
|
||||
type: list
|
||||
name: Main
|
||||
|
||||
### menu tune ###
|
||||
[menu __main __tune]
|
||||
type: list
|
||||
enable: {printer.idle_timeout.state == "Printing"}
|
||||
name: Afstellen
|
||||
|
||||
[menu __main __tune __speed]
|
||||
type: input
|
||||
name: Snelheid: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.gcode_move.speed_factor}
|
||||
input_min: 0.01
|
||||
input_max: 5
|
||||
input_step: 0.01
|
||||
realtime: True
|
||||
gcode:
|
||||
M220 S{'%d' % (menu.input*100)}
|
||||
|
||||
[menu __main __tune __flow]
|
||||
type: input
|
||||
name: Flow: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.gcode_move.extrude_factor}
|
||||
input_min: 0.01
|
||||
input_max: 2
|
||||
input_step: 0.01
|
||||
realtime: True
|
||||
gcode:
|
||||
M221 S{'%d' % (menu.input*100)}
|
||||
|
||||
[menu __main __tune __offsetz]
|
||||
type: input
|
||||
name: Offset Z:{'%05.3f' % menu.input}
|
||||
input: {printer.gcode_move.homing_origin.z}
|
||||
input_min: -5
|
||||
input_max: 5
|
||||
input_step: 0.005
|
||||
realtime: True
|
||||
gcode:
|
||||
SET_GCODE_OFFSET Z={'%.3f' % menu.input} MOVE=1
|
||||
|
||||
### menu virtual sdcard ###
|
||||
[menu __main __sdcard]
|
||||
type: vsdlist
|
||||
enable: {('virtual_sdcard' in printer)}
|
||||
name: SD Kaart
|
||||
|
||||
[menu __main __sdcard __start]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.virtual_sdcard.file_path and not printer.virtual_sdcard.is_active}
|
||||
name: Start printen
|
||||
gcode: M24
|
||||
|
||||
[menu __main __sdcard __resume]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "paused"}
|
||||
name: Herstart printen
|
||||
gcode:
|
||||
{% if "pause_resume" in printer %}
|
||||
RESUME
|
||||
{% else %}
|
||||
M24
|
||||
{% endif %}
|
||||
|
||||
[menu __main __sdcard __pause]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "printing"}
|
||||
name: Pauseer printen
|
||||
gcode:
|
||||
{% if "pause_resume" in printer %}
|
||||
PAUSE
|
||||
{% else %}
|
||||
M25
|
||||
{% endif %}
|
||||
|
||||
[menu __main __sdcard __cancel]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and (printer.print_stats.state == "printing" or printer.print_stats.state == "paused")}
|
||||
name: Annuleer printen
|
||||
gcode:
|
||||
{% if 'pause_resume' in printer %}
|
||||
CANCEL_PRINT
|
||||
{% else %}
|
||||
M25
|
||||
M27
|
||||
M26 S0
|
||||
TURN_OFF_HEATERS
|
||||
{% if printer.toolhead.position.z <= printer.toolhead.axis_maximum.z - 5 %}
|
||||
G91
|
||||
G0 Z5 F1000
|
||||
G90
|
||||
{% endif %}
|
||||
{% endif %}
|
||||
|
||||
### menu control ###
|
||||
[menu __main __control]
|
||||
type: list
|
||||
name: Control
|
||||
|
||||
[menu __main __control __home]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home All
|
||||
gcode: G28
|
||||
|
||||
[menu __main __control __homez]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home Z
|
||||
gcode: G28 Z
|
||||
|
||||
[menu __main __control __homexy]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home X/Y
|
||||
gcode: G28 X Y
|
||||
|
||||
[menu __main __control __disable]
|
||||
type: command
|
||||
name: Steppers uit
|
||||
gcode:
|
||||
M84
|
||||
M18
|
||||
|
||||
[menu __main __control __fanonoff]
|
||||
type: input
|
||||
enable: {'fan' in printer}
|
||||
name: Koeling: {'ON ' if menu.input else 'OFF'}
|
||||
input: {printer.fan.speed}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 1
|
||||
gcode:
|
||||
M106 S{255 if menu.input else 0}
|
||||
|
||||
[menu __main __control __fanspeed]
|
||||
type: input
|
||||
enable: {'fan' in printer}
|
||||
name: Snelheid koeler: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.fan.speed}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 0.01
|
||||
gcode:
|
||||
M106 S{'%d' % (menu.input*255)}
|
||||
|
||||
[menu __main __control __caselightonoff]
|
||||
type: input
|
||||
enable: {'output_pin caselight' in printer}
|
||||
name: Verlichting: {'ON ' if menu.input else 'OFF'}
|
||||
input: {printer['output_pin caselight'].value}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 1
|
||||
gcode:
|
||||
SET_PIN PIN=caselight VALUE={1 if menu.input else 0}
|
||||
|
||||
[menu __main __control __caselightpwm]
|
||||
type: input
|
||||
enable: {'output_pin caselight' in printer}
|
||||
name: Verlichting: {'%3d' % (menu.input*100)}%
|
||||
input: {printer['output_pin caselight'].value}
|
||||
input_min: 0.0
|
||||
input_max: 1.0
|
||||
input_step: 0.01
|
||||
gcode:
|
||||
SET_PIN PIN=caselight VALUE={menu.input}
|
||||
|
||||
### menu move 10mm ###
|
||||
[menu __main __control __move_10mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats 10mm
|
||||
|
||||
[menu __main __control __move_10mm __axis_x]
|
||||
type: input
|
||||
name: Verplaats X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_y]
|
||||
type: input
|
||||
name: Verplaats Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Draai E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 1mm ###
|
||||
[menu __main __control __move_1mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats 1mm
|
||||
|
||||
[menu __main __control __move_1mm __axis_x]
|
||||
type: input
|
||||
name: Verplaats X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_y]
|
||||
type: input
|
||||
name: Verplaats Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Draai E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 0.1mm ###
|
||||
[menu __main __control __move_01mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats 0.1mm
|
||||
|
||||
[menu __main __control __move_01mm __axis_x]
|
||||
type: input
|
||||
name: Verplaats X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_y]
|
||||
type: input
|
||||
name: Verplaats Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Draai E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu temperature ###
|
||||
[menu __main __temp]
|
||||
type: list
|
||||
name: Temperatuur
|
||||
|
||||
[menu __main __temp __hotend0_target]
|
||||
type: input
|
||||
enable: {('extruder' in printer) and ('extruder' in printer.heaters.available_heaters)}
|
||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
||||
input: {printer.extruder.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __hotend1_target]
|
||||
type: input
|
||||
enable: {('extruder1' in printer) and ('extruder1' in printer.heaters.available_heaters)}
|
||||
name: {"Ex1:%3.0f (%4.0f)" % (menu.input, printer.extruder1.temperature)}
|
||||
input: {printer.extruder1.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder1.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T1 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __hotbed_target]
|
||||
type: input
|
||||
enable: {'heater_bed' in printer}
|
||||
name: {"Bed:%3.0f (%4.0f)" % (menu.input, printer.heater_bed.temperature)}
|
||||
input: {printer.heater_bed.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.heater_bed.max_temp}
|
||||
input_step: 1
|
||||
gcode: M140 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __preheat_pla]
|
||||
type: list
|
||||
name: Voorverwarmen PLA
|
||||
|
||||
[menu __main __temp __preheat_pla __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Alles voorverwarmen
|
||||
gcode:
|
||||
M140 S60
|
||||
M104 S200
|
||||
|
||||
[menu __main __temp __preheat_pla __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Hotend voorverwarmen
|
||||
gcode: M104 S200
|
||||
|
||||
[menu __main __temp __preheat_pla __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Hotbed voorverwarmen
|
||||
gcode: M140 S60
|
||||
|
||||
[menu __main __temp __preheat_abs]
|
||||
type: list
|
||||
name: Voorverwarmen ABS
|
||||
|
||||
[menu __main __temp __preheat_abs __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Alles voorverwarmen
|
||||
gcode:
|
||||
M140 S110
|
||||
M104 S245
|
||||
|
||||
[menu __main __temp __preheat_abs __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Hotend voorverwarmen
|
||||
gcode: M104 S245
|
||||
|
||||
[menu __main __temp __preheat_abs __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Hotbed voorverwarmen
|
||||
gcode: M140 S110
|
||||
|
||||
[menu __main __temp __cooldown]
|
||||
type: list
|
||||
name: Afkoelen
|
||||
|
||||
[menu __main __temp __cooldown __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Alles afkoelen
|
||||
gcode:
|
||||
M104 S0
|
||||
M140 S0
|
||||
|
||||
[menu __main __temp __cooldown __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Hotend afkoelen
|
||||
gcode: M104 S0
|
||||
|
||||
[menu __main __temp __cooldown __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Hotbed afkoelen
|
||||
gcode: M140 S0
|
||||
|
||||
### menu filament ###
|
||||
|
||||
[menu __main __filament]
|
||||
type: list
|
||||
name: Filament
|
||||
|
||||
[menu __main __filament __hotend0_target]
|
||||
type: input
|
||||
enable: {'extruder' in printer}
|
||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
||||
input: {printer.extruder.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __filament __loadf]
|
||||
type: command
|
||||
name: Fil. snel laden
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E50 F960
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __loads]
|
||||
type: command
|
||||
name: Fil. langzaam laden
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E50 F240
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __unloadf]
|
||||
type: command
|
||||
name: Fil. snel uitwerpen
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E-50 F960
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __unloads]
|
||||
type: command
|
||||
name: Fil. langzaam uitwerpen
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E-50 F240
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __feed]
|
||||
type: input
|
||||
name: Snelheid: {'%.1f' % menu.input}
|
||||
input: 5
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E{'%.1f' % menu.input} F60
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
### menu setup ###
|
||||
[menu __main __setup]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Setup
|
||||
|
||||
[menu __main __setup __save_config]
|
||||
type: command
|
||||
name: Bewaar configuratie
|
||||
gcode: SAVE_CONFIG
|
||||
|
||||
[menu __main __setup __restart]
|
||||
type: list
|
||||
name: Herstarten
|
||||
|
||||
[menu __main __setup __restart __host_restart]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Herstart host
|
||||
gcode: RESTART
|
||||
|
||||
[menu __main __setup __restart __firmware_restart]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Herstart FW
|
||||
gcode: FIRMWARE_RESTART
|
||||
|
||||
[menu __main __setup __tuning]
|
||||
type: list
|
||||
name: PID tuning
|
||||
|
||||
[menu __main __setup __tuning __hotend_pid_tuning]
|
||||
type: command
|
||||
enable: {(not printer.idle_timeout.state == "Printing") and ('extruder' in printer)}
|
||||
name: Tune Hotend PID
|
||||
gcode: PID_CALIBRATE HEATER=extruder TARGET=210 WRITE_FILE=1
|
||||
|
||||
[menu __main __setup __tuning __hotbed_pid_tuning]
|
||||
type: command
|
||||
enable: {(not printer.idle_timeout.state == "Printing") and ('heater_bed' in printer)}
|
||||
name: Tune Hotbed PID
|
||||
gcode: PID_CALIBRATE HEATER=heater_bed TARGET=60 WRITE_FILE=1
|
||||
|
||||
[menu __main __setup __calib]
|
||||
type: list
|
||||
name: Calibratie
|
||||
|
||||
[menu __main __setup __calib __bedprobe]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Bed probe
|
||||
gcode: PROBE
|
||||
|
||||
[menu __main __setup __dump]
|
||||
type: command
|
||||
name: Dump parameters
|
||||
gcode:
|
||||
{% for name1 in printer %}
|
||||
{% for name2 in printer[name1] %}
|
||||
{ action_respond_info("printer['%s'].%s = %s"
|
||||
% (name1, name2, printer[name1][name2])) }
|
||||
{% else %}
|
||||
{ action_respond_info("printer['%s'] = %s" % (name1, printer[name1])) }
|
||||
{% endfor %}
|
||||
{% endfor %}
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 28.740
|
||||
#*# pid_ki = 2.129
|
||||
#*# pid_kd = 96.998
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 50.775
|
||||
#*# pid_ki = 0.692
|
||||
#*# pid_kd = 931.084
|
||||
@@ -0,0 +1,902 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
||||
# E3 v1.2. To use this config, the firmware should be compiled for the
|
||||
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
||||
# select "Enable extra low-level configuration options" and configure
|
||||
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
||||
|
||||
# The "make flash" command does not work on the SKR mini E3. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the SKR
|
||||
# mini E3 with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# Note: This board has a design flaw in its thermistor circuits that
|
||||
# cause inaccurate temperatures (most noticeable at low temperatures).
|
||||
|
||||
# Met de DropEffect OmniDrop V2.1 is het punt links-beneden (dus het 0-punt): X = 12 en Y = 30
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB13
|
||||
dir_pin: !PB12
|
||||
enable_pin: !PB14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC0
|
||||
position_endstop: -13.5
|
||||
position_min: -13.5
|
||||
position_max: 221.5
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PB15
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB10
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PB11
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC1
|
||||
position_endstop: -29
|
||||
position_min: -29
|
||||
position_max: 206
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC6
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB0
|
||||
dir_pin: PC5
|
||||
enable_pin: !PB1
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0.0
|
||||
position_max: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC10
|
||||
run_current: 0.580
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC14
|
||||
control_pin: PA1
|
||||
#pin_up_reports_not_triggered: False
|
||||
#pin_up_touch_mode_reports_triggered: False
|
||||
x_offset: 33.7
|
||||
y_offset: -33.5
|
||||
z_offset: 2.68
|
||||
pin_move_time: 0.680
|
||||
|
||||
[bed_screws]
|
||||
screw1: 32,32
|
||||
screw2: 203,32
|
||||
screw3: 203,203
|
||||
screw4: 32,203
|
||||
#screw5: 117,117
|
||||
|
||||
[bed_mesh]
|
||||
speed: 80
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 40,40
|
||||
mesh_max: 200,200
|
||||
probe_count: 5,5
|
||||
|
||||
[extruder]
|
||||
# DropEffect OmniaDrop V2.1
|
||||
step_pin: PB3
|
||||
dir_pin: PB4
|
||||
enable_pin: !PD2
|
||||
microsteps: 16
|
||||
gear_ratio: 5:1
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC8
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA0
|
||||
#control: pid
|
||||
#pid_Kp: 21.527
|
||||
#pid_Ki: 1.063
|
||||
#pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC11
|
||||
run_current: 0.500
|
||||
hold_current: 0.400
|
||||
stealthchop_threshold: 5
|
||||
|
||||
[heater_fan my_nozzle_fan]
|
||||
# Aansturing via PT-DET pinout
|
||||
pin: PC12
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PC9
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC3
|
||||
#control: pid
|
||||
#pid_Kp: 54.027
|
||||
#pid_Ki: 0.770
|
||||
#pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA8
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[static_digital_output usb_pullup_enable]
|
||||
pins: !PC13
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: EXP1_7
|
||||
sclk_pin: EXP1_6
|
||||
sid_pin: EXP1_8
|
||||
encoder_pins: ^EXP1_5, ^EXP1_3
|
||||
click_pin: ^!EXP1_2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
[virtual_sdcard]
|
||||
path: ~/gcode_files
|
||||
|
||||
[display_status]
|
||||
|
||||
[pause_resume]
|
||||
|
||||
[gcode_macro PAUSE]
|
||||
description: Pause the actual running print
|
||||
rename_existing: PAUSE_BASE
|
||||
# change this if you need more or less extrusion
|
||||
variable_extrude: 1.0
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
##### set park positon for x and y #####
|
||||
# default is your max posion from your printer.cfg
|
||||
{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
|
||||
{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
|
||||
##### calculate save lift position #####
|
||||
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
||||
{% set act_z = printer.toolhead.position.z|float %}
|
||||
{% if act_z < (max_z - 2.0) %}
|
||||
{% set z_safe = 2.0 %}
|
||||
{% else %}
|
||||
{% set z_safe = max_z - act_z %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
PAUSE_BASE
|
||||
G91
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G1 E-{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
{% if "xyz" in printer.toolhead.homed_axes %}
|
||||
G1 Z{z_safe} F900
|
||||
G90
|
||||
G1 X{x_park} Y{y_park} F6000
|
||||
{% else %}
|
||||
{action_respond_info("Printer not homed")}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro RESUME]
|
||||
description: Resume the actual running print
|
||||
rename_existing: RESUME_BASE
|
||||
gcode:
|
||||
##### read E from pause macro #####
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
#### get VELOCITY parameter if specified ####
|
||||
{% if 'VELOCITY' in params|upper %}
|
||||
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
||||
{%else %}
|
||||
{% set get_params = "" %}
|
||||
{% endif %}
|
||||
##### end of definitions #####
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G91
|
||||
G1 E{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
RESUME_BASE {get_params}
|
||||
|
||||
[gcode_macro CANCEL_PRINT]
|
||||
description: Cancel the actual running print
|
||||
rename_existing: CANCEL_PRINT_BASE
|
||||
gcode:
|
||||
TURN_OFF_HEATERS
|
||||
CANCEL_PRINT_BASE
|
||||
|
||||
# The print bed can move so far to the front, that the nozzle can reach the
|
||||
# plastic cover of the print bed heater cable (only when the bed is moved by
|
||||
# hand). By homing the Y axis before the X axis, it is ensured the nozzle will
|
||||
# not melt through the plastic part.
|
||||
# BEWARE: You will lose the ability to home axes individually. The printer will
|
||||
# always home all axes for every G28 command.
|
||||
#[homing_override]
|
||||
#gcode:
|
||||
# G28 Y0
|
||||
# G28 X0
|
||||
# G28 Z0
|
||||
|
||||
# ================================================================================
|
||||
# GCode Macro: START_PRINT
|
||||
# Add START_PRINT in your slicers starting script.
|
||||
# ================================================================================
|
||||
[gcode_macro START_PRINT]
|
||||
gcode:
|
||||
G28; Home all axes
|
||||
BED_MESH_CALIBRATE
|
||||
G92 E0; Reset Extruder
|
||||
G1 Z5.0 F3000; Move Z Axis up little to prevent scratching of Heat Bed
|
||||
G1 X0.1 Y20 Z0.3 F5000.0; Move to start position
|
||||
G1 X0.1 Y200.0 Z0.3 F1500.0 E15; Draw the first line
|
||||
G1 X0.4 Y200.0 Z0.3 F5000.0; Move to side a little
|
||||
G1 X0.4 Y20 Z0.3 F1500.0 E30; Draw the second line
|
||||
G92 E0; Reset Extruder
|
||||
G1 Z5.0 F3000; Move Z Axis up little to prevent scratching of Heat Bed
|
||||
|
||||
# ================================================================================
|
||||
# GCode Macro: END_PRINT
|
||||
# Add END_PRINT in your slicers ending script
|
||||
# ================================================================================
|
||||
[gcode_macro END_PRINT]
|
||||
gcode:
|
||||
G91; Relative Positioning
|
||||
G1 Z+10; Move Z up so it doesn't hit anything
|
||||
G90; Absolute Positioning
|
||||
G1 Y190 F1500; bring Y up front
|
||||
# G10 ; set tool offset? or retract?
|
||||
# G1 E-10 F300; Retrack-10
|
||||
G1 X10 Y220 F2000; Move to X10, Y220
|
||||
M104 S0; Turn off Extruder temperature (set it to 0)
|
||||
M140 S0; Turn off Bed temperature (set it to 0)
|
||||
M106 S0; turn off cooling fan
|
||||
M84; Disable steppers
|
||||
# ================================================================================
|
||||
# GCode Macro G29
|
||||
# Fires when G29 is sent to the printer
|
||||
# ================================================================================
|
||||
[gcode_macro G29]
|
||||
gcode:
|
||||
G1 Z10 F600
|
||||
G4 P200
|
||||
G1 Z10 F600
|
||||
G4 P100
|
||||
|
||||
### menu main ###
|
||||
[menu __main]
|
||||
type: list
|
||||
name: Main
|
||||
|
||||
### menu tune ###
|
||||
[menu __main __tune]
|
||||
type: list
|
||||
enable: {printer.idle_timeout.state == "Printing"}
|
||||
name: Afstellen
|
||||
|
||||
[menu __main __tune __speed]
|
||||
type: input
|
||||
name: Snelheid: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.gcode_move.speed_factor}
|
||||
input_min: 0.01
|
||||
input_max: 5
|
||||
input_step: 0.01
|
||||
realtime: True
|
||||
gcode:
|
||||
M220 S{'%d' % (menu.input*100)}
|
||||
|
||||
[menu __main __tune __flow]
|
||||
type: input
|
||||
name: Flow: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.gcode_move.extrude_factor}
|
||||
input_min: 0.01
|
||||
input_max: 2
|
||||
input_step: 0.01
|
||||
realtime: True
|
||||
gcode:
|
||||
M221 S{'%d' % (menu.input*100)}
|
||||
|
||||
[menu __main __tune __offsetz]
|
||||
type: input
|
||||
name: Offset Z:{'%05.3f' % menu.input}
|
||||
input: {printer.gcode_move.homing_origin.z}
|
||||
input_min: -5
|
||||
input_max: 5
|
||||
input_step: 0.005
|
||||
realtime: True
|
||||
gcode:
|
||||
SET_GCODE_OFFSET Z={'%.3f' % menu.input} MOVE=1
|
||||
|
||||
### menu virtual sdcard ###
|
||||
[menu __main __sdcard]
|
||||
type: vsdlist
|
||||
enable: {('virtual_sdcard' in printer)}
|
||||
name: SD Kaart
|
||||
|
||||
[menu __main __sdcard __start]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.virtual_sdcard.file_path and not printer.virtual_sdcard.is_active}
|
||||
name: Start printen
|
||||
gcode: M24
|
||||
|
||||
[menu __main __sdcard __resume]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "paused"}
|
||||
name: Herstart printen
|
||||
gcode:
|
||||
{% if "pause_resume" in printer %}
|
||||
RESUME
|
||||
{% else %}
|
||||
M24
|
||||
{% endif %}
|
||||
|
||||
[menu __main __sdcard __pause]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "printing"}
|
||||
name: Pauseer printen
|
||||
gcode:
|
||||
{% if "pause_resume" in printer %}
|
||||
PAUSE
|
||||
{% else %}
|
||||
M25
|
||||
{% endif %}
|
||||
|
||||
[menu __main __sdcard __cancel]
|
||||
type: command
|
||||
enable: {('virtual_sdcard' in printer) and (printer.print_stats.state == "printing" or printer.print_stats.state == "paused")}
|
||||
name: Annuleer printen
|
||||
gcode:
|
||||
{% if 'pause_resume' in printer %}
|
||||
CANCEL_PRINT
|
||||
{% else %}
|
||||
M25
|
||||
M27
|
||||
M26 S0
|
||||
TURN_OFF_HEATERS
|
||||
{% if printer.toolhead.position.z <= printer.toolhead.axis_maximum.z - 5 %}
|
||||
G91
|
||||
G0 Z5 F1000
|
||||
G90
|
||||
{% endif %}
|
||||
{% endif %}
|
||||
|
||||
### menu control ###
|
||||
[menu __main __control]
|
||||
type: list
|
||||
name: Control
|
||||
|
||||
[menu __main __control __home]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home All
|
||||
gcode: G28
|
||||
|
||||
[menu __main __control __homez]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home Z
|
||||
gcode: G28 Z
|
||||
|
||||
[menu __main __control __homexy]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Home X/Y
|
||||
gcode: G28 X Y
|
||||
|
||||
[menu __main __control __disable]
|
||||
type: command
|
||||
name: Steppers uit
|
||||
gcode:
|
||||
M84
|
||||
M18
|
||||
|
||||
[menu __main __control __fanonoff]
|
||||
type: input
|
||||
enable: {'fan' in printer}
|
||||
name: Koeling: {'ON ' if menu.input else 'OFF'}
|
||||
input: {printer.fan.speed}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 1
|
||||
gcode:
|
||||
M106 S{255 if menu.input else 0}
|
||||
|
||||
[menu __main __control __fanspeed]
|
||||
type: input
|
||||
enable: {'fan' in printer}
|
||||
name: Snelheid koeler: {'%3d' % (menu.input*100)}%
|
||||
input: {printer.fan.speed}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 0.01
|
||||
gcode:
|
||||
M106 S{'%d' % (menu.input*255)}
|
||||
|
||||
[menu __main __control __caselightonoff]
|
||||
type: input
|
||||
enable: {'output_pin caselight' in printer}
|
||||
name: Verlichting: {'ON ' if menu.input else 'OFF'}
|
||||
input: {printer['output_pin caselight'].value}
|
||||
input_min: 0
|
||||
input_max: 1
|
||||
input_step: 1
|
||||
gcode:
|
||||
SET_PIN PIN=caselight VALUE={1 if menu.input else 0}
|
||||
|
||||
[menu __main __control __caselightpwm]
|
||||
type: input
|
||||
enable: {'output_pin caselight' in printer}
|
||||
name: Verlichting: {'%3d' % (menu.input*100)}%
|
||||
input: {printer['output_pin caselight'].value}
|
||||
input_min: 0.0
|
||||
input_max: 1.0
|
||||
input_step: 0.01
|
||||
gcode:
|
||||
SET_PIN PIN=caselight VALUE={menu.input}
|
||||
|
||||
### menu move 10mm ###
|
||||
[menu __main __control __move_10mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats 10mm
|
||||
|
||||
[menu __main __control __move_10mm __axis_x]
|
||||
type: input
|
||||
name: Verplaats X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_y]
|
||||
type: input
|
||||
name: Verplaats Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_10mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Draai E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 10.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 1mm ###
|
||||
[menu __main __control __move_1mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats 1mm
|
||||
|
||||
[menu __main __control __move_1mm __axis_x]
|
||||
type: input
|
||||
name: Verplaats X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_y]
|
||||
type: input
|
||||
name: Verplaats Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_1mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Draai E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 1.0
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu move 0.1mm ###
|
||||
[menu __main __control __move_01mm]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats 0.1mm
|
||||
|
||||
[menu __main __control __move_01mm __axis_x]
|
||||
type: input
|
||||
name: Verplaats X:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.x}
|
||||
input_min: {printer.toolhead.axis_minimum.x}
|
||||
input_max: {printer.toolhead.axis_maximum.x}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 X{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_y]
|
||||
type: input
|
||||
name: Verplaats Y:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.y}
|
||||
input_min: {printer.toolhead.axis_minimum.y}
|
||||
input_max: {printer.toolhead.axis_maximum.y}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Y{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_z]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Verplaats Z:{'%05.1f' % menu.input}
|
||||
input: {printer.gcode_move.gcode_position.z}
|
||||
input_min: 0
|
||||
input_max: {printer.toolhead.axis_maximum.z}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
G90
|
||||
G1 Z{menu.input}
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
[menu __main __control __move_01mm __axis_e]
|
||||
type: input
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Draai E:{'%+06.1f' % menu.input}
|
||||
input: 0
|
||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__move__axis
|
||||
M83
|
||||
G1 E{menu.input} F240
|
||||
RESTORE_GCODE_STATE NAME=__move__axis
|
||||
|
||||
### menu temperature ###
|
||||
[menu __main __temp]
|
||||
type: list
|
||||
name: Temperatuur
|
||||
|
||||
[menu __main __temp __hotend0_target]
|
||||
type: input
|
||||
enable: {('extruder' in printer) and ('extruder' in printer.heaters.available_heaters)}
|
||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
||||
input: {printer.extruder.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __hotend1_target]
|
||||
type: input
|
||||
enable: {('extruder1' in printer) and ('extruder1' in printer.heaters.available_heaters)}
|
||||
name: {"Ex1:%3.0f (%4.0f)" % (menu.input, printer.extruder1.temperature)}
|
||||
input: {printer.extruder1.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder1.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T1 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __hotbed_target]
|
||||
type: input
|
||||
enable: {'heater_bed' in printer}
|
||||
name: {"Bed:%3.0f (%4.0f)" % (menu.input, printer.heater_bed.temperature)}
|
||||
input: {printer.heater_bed.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.heater_bed.max_temp}
|
||||
input_step: 1
|
||||
gcode: M140 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __temp __preheat_pla]
|
||||
type: list
|
||||
name: Voorverwarmen PLA
|
||||
|
||||
[menu __main __temp __preheat_pla __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Alles voorverwarmen
|
||||
gcode:
|
||||
M140 S60
|
||||
M104 S200
|
||||
|
||||
[menu __main __temp __preheat_pla __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Hotend voorverwarmen
|
||||
gcode: M104 S200
|
||||
|
||||
[menu __main __temp __preheat_pla __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Hotbed voorverwarmen
|
||||
gcode: M140 S60
|
||||
|
||||
[menu __main __temp __preheat_abs]
|
||||
type: list
|
||||
name: Voorverwarmen ABS
|
||||
|
||||
[menu __main __temp __preheat_abs __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Alles voorverwarmen
|
||||
gcode:
|
||||
M140 S110
|
||||
M104 S245
|
||||
|
||||
[menu __main __temp __preheat_abs __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Hotend voorverwarmen
|
||||
gcode: M104 S245
|
||||
|
||||
[menu __main __temp __preheat_abs __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Hotbed voorverwarmen
|
||||
gcode: M140 S110
|
||||
|
||||
[menu __main __temp __cooldown]
|
||||
type: list
|
||||
name: Afkoelen
|
||||
|
||||
[menu __main __temp __cooldown __all]
|
||||
type: command
|
||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
||||
name: Alles afkoelen
|
||||
gcode:
|
||||
M104 S0
|
||||
M140 S0
|
||||
|
||||
[menu __main __temp __cooldown __hotend]
|
||||
type: command
|
||||
enable: {'extruder' in printer}
|
||||
name: Hotend afkoelen
|
||||
gcode: M104 S0
|
||||
|
||||
[menu __main __temp __cooldown __hotbed]
|
||||
type: command
|
||||
enable: {'heater_bed' in printer}
|
||||
name: Hotbed afkoelen
|
||||
gcode: M140 S0
|
||||
|
||||
### menu filament ###
|
||||
|
||||
[menu __main __filament]
|
||||
type: list
|
||||
name: Filament
|
||||
|
||||
[menu __main __filament __hotend0_target]
|
||||
type: input
|
||||
enable: {'extruder' in printer}
|
||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
||||
input: {printer.extruder.target}
|
||||
input_min: 0
|
||||
input_max: {printer.configfile.config.extruder.max_temp}
|
||||
input_step: 1
|
||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
||||
|
||||
[menu __main __filament __loadf]
|
||||
type: command
|
||||
name: Fil. snel laden
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E50 F960
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __loads]
|
||||
type: command
|
||||
name: Fil. langzaam laden
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E50 F240
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __unloadf]
|
||||
type: command
|
||||
name: Fil. snel uitwerpen
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E-50 F960
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __unloads]
|
||||
type: command
|
||||
name: Fil. langzaam uitwerpen
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E-50 F240
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
[menu __main __filament __feed]
|
||||
type: input
|
||||
name: Snelheid: {'%.1f' % menu.input}
|
||||
input: 5
|
||||
input_step: 0.1
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=__filament__load
|
||||
M83
|
||||
G1 E{'%.1f' % menu.input} F60
|
||||
RESTORE_GCODE_STATE NAME=__filament__load
|
||||
|
||||
### menu setup ###
|
||||
[menu __main __setup]
|
||||
type: list
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Setup
|
||||
|
||||
[menu __main __setup __save_config]
|
||||
type: command
|
||||
name: Bewaar configuratie
|
||||
gcode: SAVE_CONFIG
|
||||
|
||||
[menu __main __setup __restart]
|
||||
type: list
|
||||
name: Herstarten
|
||||
|
||||
[menu __main __setup __restart __host_restart]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Herstart host
|
||||
gcode: RESTART
|
||||
|
||||
[menu __main __setup __restart __firmware_restart]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Herstart FW
|
||||
gcode: FIRMWARE_RESTART
|
||||
|
||||
[menu __main __setup __tuning]
|
||||
type: list
|
||||
name: PID tuning
|
||||
|
||||
[menu __main __setup __tuning __hotend_pid_tuning]
|
||||
type: command
|
||||
enable: {(not printer.idle_timeout.state == "Printing") and ('extruder' in printer)}
|
||||
name: Tune Hotend PID
|
||||
gcode: PID_CALIBRATE HEATER=extruder TARGET=210 WRITE_FILE=1
|
||||
|
||||
[menu __main __setup __tuning __hotbed_pid_tuning]
|
||||
type: command
|
||||
enable: {(not printer.idle_timeout.state == "Printing") and ('heater_bed' in printer)}
|
||||
name: Tune Hotbed PID
|
||||
gcode: PID_CALIBRATE HEATER=heater_bed TARGET=60 WRITE_FILE=1
|
||||
|
||||
[menu __main __setup __calib]
|
||||
type: list
|
||||
name: Calibratie
|
||||
|
||||
[menu __main __setup __calib __bedprobe]
|
||||
type: command
|
||||
enable: {not printer.idle_timeout.state == "Printing"}
|
||||
name: Bed probe
|
||||
gcode: PROBE
|
||||
|
||||
[menu __main __setup __dump]
|
||||
type: command
|
||||
name: Dump parameters
|
||||
gcode:
|
||||
{% for name1 in printer %}
|
||||
{% for name2 in printer[name1] %}
|
||||
{ action_respond_info("printer['%s'].%s = %s"
|
||||
% (name1, name2, printer[name1][name2])) }
|
||||
{% else %}
|
||||
{ action_respond_info("printer['%s'] = %s" % (name1, printer[name1])) }
|
||||
{% endfor %}
|
||||
{% endfor %}
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 28.195
|
||||
#*# pid_ki = 1.880
|
||||
#*# pid_kd = 105.733
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 50.775
|
||||
#*# pid_ki = 0.692
|
||||
#*# pid_kd = 931.084
|
||||
1010
klipper/DNV-TPU-Ender3/klipper_config/printer.cfg
Normal file
1010
klipper/DNV-TPU-Ender3/klipper_config/printer.cfg
Normal file
File diff suppressed because it is too large
Load Diff
Reference in New Issue
Block a user