Delete klipper/DNV-TPU-Ender3/printer-20220104_172505.cfg
This commit is contained in:
@@ -1,907 +0,0 @@
|
|||||||
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
|
||||||
# E3 v1.2. To use this config, the firmware should be compiled for the
|
|
||||||
# STM32F103 with a "28KiB bootloader" and USB communication. Also,
|
|
||||||
# select "Enable extra low-level configuration options" and configure
|
|
||||||
# "GPIO pins to set at micro-controller startup" to "!PC13".
|
|
||||||
|
|
||||||
# The "make flash" command does not work on the SKR mini E3. Instead,
|
|
||||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
|
||||||
# file named "firmware.bin" on an SD card and then restart the SKR
|
|
||||||
# mini E3 with that SD card.
|
|
||||||
|
|
||||||
# See docs/Config_Reference.md for a description of parameters.
|
|
||||||
|
|
||||||
# Note: This board has a design flaw in its thermistor circuits that
|
|
||||||
# cause inaccurate temperatures (most noticeable at low temperatures).
|
|
||||||
|
|
||||||
[stepper_x]
|
|
||||||
step_pin: PB13
|
|
||||||
dir_pin: !PB12
|
|
||||||
enable_pin: !PB14
|
|
||||||
microsteps: 16
|
|
||||||
rotation_distance: 40
|
|
||||||
endstop_pin: ^PC0
|
|
||||||
position_endstop: 0
|
|
||||||
position_max: 235
|
|
||||||
homing_speed: 50
|
|
||||||
|
|
||||||
[tmc2209 stepper_x]
|
|
||||||
uart_pin: PB15
|
|
||||||
run_current: 0.580
|
|
||||||
stealthchop_threshold: 999999
|
|
||||||
|
|
||||||
[stepper_y]
|
|
||||||
step_pin: PB10
|
|
||||||
dir_pin: !PB2
|
|
||||||
enable_pin: !PB11
|
|
||||||
microsteps: 16
|
|
||||||
rotation_distance: 40
|
|
||||||
endstop_pin: ^PC1
|
|
||||||
position_endstop: 0
|
|
||||||
position_max: 235
|
|
||||||
homing_speed: 50
|
|
||||||
|
|
||||||
[tmc2209 stepper_y]
|
|
||||||
uart_pin: PC6
|
|
||||||
run_current: 0.580
|
|
||||||
stealthchop_threshold: 999999
|
|
||||||
|
|
||||||
[stepper_z]
|
|
||||||
step_pin: PB0
|
|
||||||
dir_pin: PC5
|
|
||||||
enable_pin: !PB1
|
|
||||||
microsteps: 16
|
|
||||||
rotation_distance: 8
|
|
||||||
endstop_pin: ^PC2
|
|
||||||
position_endstop: 0.0
|
|
||||||
position_max: 250
|
|
||||||
|
|
||||||
[tmc2209 stepper_z]
|
|
||||||
uart_pin: PC10
|
|
||||||
run_current: 0.580
|
|
||||||
stealthchop_threshold: 999999
|
|
||||||
|
|
||||||
[bltouch]
|
|
||||||
sensor_pin: ^PC14 ;mine uses the Z pin for sensor
|
|
||||||
control_pin: PA1
|
|
||||||
pin_up_reports_not_triggered: False
|
|
||||||
pin_up_touch_mode_reports_triggered: False
|
|
||||||
x_offset: 32.4
|
|
||||||
y_offset: -34.9
|
|
||||||
z_offset: 1.6
|
|
||||||
pin_move_time: 1.5
|
|
||||||
|
|
||||||
[extruder]
|
|
||||||
# DropEffect OmniaDrop V2.1
|
|
||||||
step_pin: PB3
|
|
||||||
dir_pin: !PB4
|
|
||||||
enable_pin: !PD2
|
|
||||||
microsteps: 16
|
|
||||||
gear_ratio: 5:1
|
|
||||||
rotation_distance: 33.500
|
|
||||||
nozzle_diameter: 0.400
|
|
||||||
filament_diameter: 1.750
|
|
||||||
heater_pin: PC8
|
|
||||||
sensor_type: EPCOS 100K B57560G104F
|
|
||||||
sensor_pin: PA0
|
|
||||||
control: pid
|
|
||||||
pid_Kp: 21.527
|
|
||||||
pid_Ki: 1.063
|
|
||||||
pid_Kd: 108.982
|
|
||||||
min_temp: 0
|
|
||||||
max_temp: 285
|
|
||||||
|
|
||||||
[tmc2209 extruder]
|
|
||||||
uart_pin: PC11
|
|
||||||
run_current: 0.500
|
|
||||||
stealthchop_threshold: 999999
|
|
||||||
|
|
||||||
[heater_bed]
|
|
||||||
heater_pin: PC9
|
|
||||||
sensor_type: EPCOS 100K B57560G104F
|
|
||||||
sensor_pin: PC3
|
|
||||||
control: pid
|
|
||||||
pid_Kp: 54.027
|
|
||||||
pid_Ki: 0.770
|
|
||||||
pid_Kd: 948.182
|
|
||||||
min_temp: 0
|
|
||||||
max_temp: 130
|
|
||||||
|
|
||||||
[fan]
|
|
||||||
pin: PA8
|
|
||||||
|
|
||||||
[mcu]
|
|
||||||
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_32FFDA054158323011792557-if00
|
|
||||||
|
|
||||||
[printer]
|
|
||||||
kinematics: cartesian
|
|
||||||
max_velocity: 300
|
|
||||||
max_accel: 3000
|
|
||||||
max_z_velocity: 5
|
|
||||||
max_z_accel: 100
|
|
||||||
|
|
||||||
[static_digital_output usb_pullup_enable]
|
|
||||||
pins: !PC13
|
|
||||||
|
|
||||||
[board_pins]
|
|
||||||
aliases:
|
|
||||||
# EXP1 header
|
|
||||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
|
||||||
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
|
||||||
|
|
||||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
||||||
|
|
||||||
[display]
|
|
||||||
lcd_type: st7920
|
|
||||||
cs_pin: EXP1_7
|
|
||||||
sclk_pin: EXP1_6
|
|
||||||
sid_pin: EXP1_8
|
|
||||||
encoder_pins: ^EXP1_5, ^EXP1_3
|
|
||||||
click_pin: ^!EXP1_2
|
|
||||||
|
|
||||||
[output_pin beeper]
|
|
||||||
pin: EXP1_1
|
|
||||||
|
|
||||||
[virtual_sdcard]
|
|
||||||
path: ~/gcode_files
|
|
||||||
|
|
||||||
[display_status]
|
|
||||||
|
|
||||||
[pause_resume]
|
|
||||||
|
|
||||||
[gcode_macro PAUSE]
|
|
||||||
description: Pause the actual running print
|
|
||||||
rename_existing: PAUSE_BASE
|
|
||||||
# change this if you need more or less extrusion
|
|
||||||
variable_extrude: 1.0
|
|
||||||
gcode:
|
|
||||||
##### read E from pause macro #####
|
|
||||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
|
||||||
##### set park positon for x and y #####
|
|
||||||
# default is your max posion from your printer.cfg
|
|
||||||
{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
|
|
||||||
{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
|
|
||||||
##### calculate save lift position #####
|
|
||||||
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
|
||||||
{% set act_z = printer.toolhead.position.z|float %}
|
|
||||||
{% if act_z < (max_z - 2.0) %}
|
|
||||||
{% set z_safe = 2.0 %}
|
|
||||||
{% else %}
|
|
||||||
{% set z_safe = max_z - act_z %}
|
|
||||||
{% endif %}
|
|
||||||
##### end of definitions #####
|
|
||||||
PAUSE_BASE
|
|
||||||
G91
|
|
||||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
|
||||||
G1 E-{E} F2100
|
|
||||||
{% else %}
|
|
||||||
{action_respond_info("Extruder not hot enough")}
|
|
||||||
{% endif %}
|
|
||||||
{% if "xyz" in printer.toolhead.homed_axes %}
|
|
||||||
G1 Z{z_safe} F900
|
|
||||||
G90
|
|
||||||
G1 X{x_park} Y{y_park} F6000
|
|
||||||
{% else %}
|
|
||||||
{action_respond_info("Printer not homed")}
|
|
||||||
{% endif %}
|
|
||||||
|
|
||||||
[gcode_macro RESUME]
|
|
||||||
description: Resume the actual running print
|
|
||||||
rename_existing: RESUME_BASE
|
|
||||||
gcode:
|
|
||||||
##### read E from pause macro #####
|
|
||||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
|
||||||
#### get VELOCITY parameter if specified ####
|
|
||||||
{% if 'VELOCITY' in params|upper %}
|
|
||||||
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
|
||||||
{%else %}
|
|
||||||
{% set get_params = "" %}
|
|
||||||
{% endif %}
|
|
||||||
##### end of definitions #####
|
|
||||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
|
||||||
G91
|
|
||||||
G1 E{E} F2100
|
|
||||||
{% else %}
|
|
||||||
{action_respond_info("Extruder not hot enough")}
|
|
||||||
{% endif %}
|
|
||||||
RESUME_BASE {get_params}
|
|
||||||
|
|
||||||
[gcode_macro CANCEL_PRINT]
|
|
||||||
description: Cancel the actual running print
|
|
||||||
rename_existing: CANCEL_PRINT_BASE
|
|
||||||
gcode:
|
|
||||||
TURN_OFF_HEATERS
|
|
||||||
CANCEL_PRINT_BASE
|
|
||||||
|
|
||||||
# The print bed can move so far to the front, that the nozzle can reach the
|
|
||||||
# plastic cover of the print bed heater cable (only when the bed is moved by
|
|
||||||
# hand). By homing the Y axis before the X axis, it is ensured the nozzle will
|
|
||||||
# not melt through the plastic part.
|
|
||||||
# BEWARE: You will lose the ability to home axes individually. The printer will
|
|
||||||
# always home all axes for every G28 command.
|
|
||||||
#[homing_override]
|
|
||||||
#gcode:
|
|
||||||
# G28 Y0
|
|
||||||
# G28 X0
|
|
||||||
# G28 Z0
|
|
||||||
|
|
||||||
[bed_screws]
|
|
||||||
screw1: 32,32
|
|
||||||
screw2: 203,32
|
|
||||||
screw3: 203,203
|
|
||||||
screw4: 32,203
|
|
||||||
screw5: 117,117
|
|
||||||
|
|
||||||
### menu main ###
|
|
||||||
[menu __main]
|
|
||||||
type: list
|
|
||||||
name: Main
|
|
||||||
|
|
||||||
### menu tune ###
|
|
||||||
[menu __main __tune]
|
|
||||||
type: list
|
|
||||||
enable: {printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Tune
|
|
||||||
|
|
||||||
[menu __main __tune __speed]
|
|
||||||
type: input
|
|
||||||
name: Speed: {'%3d' % (menu.input*100)}%
|
|
||||||
input: {printer.gcode_move.speed_factor}
|
|
||||||
input_min: 0.01
|
|
||||||
input_max: 5
|
|
||||||
input_step: 0.01
|
|
||||||
realtime: True
|
|
||||||
gcode:
|
|
||||||
M220 S{'%d' % (menu.input*100)}
|
|
||||||
|
|
||||||
[menu __main __tune __flow]
|
|
||||||
type: input
|
|
||||||
name: Flow: {'%3d' % (menu.input*100)}%
|
|
||||||
input: {printer.gcode_move.extrude_factor}
|
|
||||||
input_min: 0.01
|
|
||||||
input_max: 2
|
|
||||||
input_step: 0.01
|
|
||||||
realtime: True
|
|
||||||
gcode:
|
|
||||||
M221 S{'%d' % (menu.input*100)}
|
|
||||||
|
|
||||||
[menu __main __tune __offsetz]
|
|
||||||
type: input
|
|
||||||
name: Offset Z:{'%05.3f' % menu.input}
|
|
||||||
input: {printer.gcode_move.homing_origin.z}
|
|
||||||
input_min: -5
|
|
||||||
input_max: 5
|
|
||||||
input_step: 0.005
|
|
||||||
realtime: True
|
|
||||||
gcode:
|
|
||||||
SET_GCODE_OFFSET Z={'%.3f' % menu.input} MOVE=1
|
|
||||||
|
|
||||||
|
|
||||||
### menu octoprint ###
|
|
||||||
[menu __main __octoprint]
|
|
||||||
type: list
|
|
||||||
name: OctoPrint
|
|
||||||
|
|
||||||
[menu __main __octoprint __pause]
|
|
||||||
type: command
|
|
||||||
enable: {printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Pause printing
|
|
||||||
gcode:
|
|
||||||
{action_respond_info('action:pause')}
|
|
||||||
|
|
||||||
[menu __main __octoprint __resume]
|
|
||||||
type: command
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Resume printing
|
|
||||||
gcode:
|
|
||||||
{action_respond_info('action:resume')}
|
|
||||||
|
|
||||||
[menu __main __octoprint __abort]
|
|
||||||
type: command
|
|
||||||
enable: {printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Abort printing
|
|
||||||
gcode:
|
|
||||||
{action_respond_info('action:cancel')}
|
|
||||||
|
|
||||||
### menu virtual sdcard ###
|
|
||||||
[menu __main __sdcard]
|
|
||||||
type: vsdlist
|
|
||||||
enable: {('virtual_sdcard' in printer)}
|
|
||||||
name: SD Card
|
|
||||||
|
|
||||||
[menu __main __sdcard __start]
|
|
||||||
type: command
|
|
||||||
enable: {('virtual_sdcard' in printer) and printer.virtual_sdcard.file_path and not printer.virtual_sdcard.is_active}
|
|
||||||
name: Start printing
|
|
||||||
gcode: M24
|
|
||||||
|
|
||||||
[menu __main __sdcard __resume]
|
|
||||||
type: command
|
|
||||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "paused"}
|
|
||||||
name: Resume printing
|
|
||||||
gcode:
|
|
||||||
{% if "pause_resume" in printer %}
|
|
||||||
RESUME
|
|
||||||
{% else %}
|
|
||||||
M24
|
|
||||||
{% endif %}
|
|
||||||
|
|
||||||
[menu __main __sdcard __pause]
|
|
||||||
type: command
|
|
||||||
enable: {('virtual_sdcard' in printer) and printer.print_stats.state == "printing"}
|
|
||||||
name: Pause printing
|
|
||||||
gcode:
|
|
||||||
{% if "pause_resume" in printer %}
|
|
||||||
PAUSE
|
|
||||||
{% else %}
|
|
||||||
M25
|
|
||||||
{% endif %}
|
|
||||||
|
|
||||||
[menu __main __sdcard __cancel]
|
|
||||||
type: command
|
|
||||||
enable: {('virtual_sdcard' in printer) and (printer.print_stats.state == "printing" or printer.print_stats.state == "paused")}
|
|
||||||
name: Cancel printing
|
|
||||||
gcode:
|
|
||||||
{% if 'pause_resume' in printer %}
|
|
||||||
CANCEL_PRINT
|
|
||||||
{% else %}
|
|
||||||
M25
|
|
||||||
M27
|
|
||||||
M26 S0
|
|
||||||
TURN_OFF_HEATERS
|
|
||||||
{% if printer.toolhead.position.z <= printer.toolhead.axis_maximum.z - 5 %}
|
|
||||||
G91
|
|
||||||
G0 Z5 F1000
|
|
||||||
G90
|
|
||||||
{% endif %}
|
|
||||||
{% endif %}
|
|
||||||
|
|
||||||
### menu control ###
|
|
||||||
[menu __main __control]
|
|
||||||
type: list
|
|
||||||
name: Control
|
|
||||||
|
|
||||||
[menu __main __control __home]
|
|
||||||
type: command
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Home All
|
|
||||||
gcode: G28
|
|
||||||
|
|
||||||
[menu __main __control __homez]
|
|
||||||
type: command
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Home Z
|
|
||||||
gcode: G28 Z
|
|
||||||
|
|
||||||
[menu __main __control __homexy]
|
|
||||||
type: command
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Home X/Y
|
|
||||||
gcode: G28 X Y
|
|
||||||
|
|
||||||
[menu __main __control __disable]
|
|
||||||
type: command
|
|
||||||
name: Steppers off
|
|
||||||
gcode:
|
|
||||||
M84
|
|
||||||
M18
|
|
||||||
|
|
||||||
[menu __main __control __fanonoff]
|
|
||||||
type: input
|
|
||||||
enable: {'fan' in printer}
|
|
||||||
name: Fan: {'ON ' if menu.input else 'OFF'}
|
|
||||||
input: {printer.fan.speed}
|
|
||||||
input_min: 0
|
|
||||||
input_max: 1
|
|
||||||
input_step: 1
|
|
||||||
gcode:
|
|
||||||
M106 S{255 if menu.input else 0}
|
|
||||||
|
|
||||||
[menu __main __control __fanspeed]
|
|
||||||
type: input
|
|
||||||
enable: {'fan' in printer}
|
|
||||||
name: Fan speed: {'%3d' % (menu.input*100)}%
|
|
||||||
input: {printer.fan.speed}
|
|
||||||
input_min: 0
|
|
||||||
input_max: 1
|
|
||||||
input_step: 0.01
|
|
||||||
gcode:
|
|
||||||
M106 S{'%d' % (menu.input*255)}
|
|
||||||
|
|
||||||
[menu __main __control __caselightonoff]
|
|
||||||
type: input
|
|
||||||
enable: {'output_pin caselight' in printer}
|
|
||||||
name: Lights: {'ON ' if menu.input else 'OFF'}
|
|
||||||
input: {printer['output_pin caselight'].value}
|
|
||||||
input_min: 0
|
|
||||||
input_max: 1
|
|
||||||
input_step: 1
|
|
||||||
gcode:
|
|
||||||
SET_PIN PIN=caselight VALUE={1 if menu.input else 0}
|
|
||||||
|
|
||||||
[menu __main __control __caselightpwm]
|
|
||||||
type: input
|
|
||||||
enable: {'output_pin caselight' in printer}
|
|
||||||
name: Lights: {'%3d' % (menu.input*100)}%
|
|
||||||
input: {printer['output_pin caselight'].value}
|
|
||||||
input_min: 0.0
|
|
||||||
input_max: 1.0
|
|
||||||
input_step: 0.01
|
|
||||||
gcode:
|
|
||||||
SET_PIN PIN=caselight VALUE={menu.input}
|
|
||||||
|
|
||||||
### menu move 10mm ###
|
|
||||||
[menu __main __control __move_10mm]
|
|
||||||
type: list
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Move 10mm
|
|
||||||
|
|
||||||
[menu __main __control __move_10mm __axis_x]
|
|
||||||
type: input
|
|
||||||
name: Move X:{'%05.1f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.x}
|
|
||||||
input_min: {printer.toolhead.axis_minimum.x}
|
|
||||||
input_max: {printer.toolhead.axis_maximum.x}
|
|
||||||
input_step: 10.0
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G90
|
|
||||||
G1 X{menu.input}
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
[menu __main __control __move_10mm __axis_y]
|
|
||||||
type: input
|
|
||||||
name: Move Y:{'%05.1f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.y}
|
|
||||||
input_min: {printer.toolhead.axis_minimum.y}
|
|
||||||
input_max: {printer.toolhead.axis_maximum.y}
|
|
||||||
input_step: 10.0
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G90
|
|
||||||
G1 Y{menu.input}
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
[menu __main __control __move_10mm __axis_z]
|
|
||||||
type: input
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Move Z:{'%05.1f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.z}
|
|
||||||
input_min: 0
|
|
||||||
input_max: {printer.toolhead.axis_maximum.z}
|
|
||||||
input_step: 10.0
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G90
|
|
||||||
G1 Z{menu.input}
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
[menu __main __control __move_10mm __axis_e]
|
|
||||||
type: input
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Move E:{'%+06.1f' % menu.input}
|
|
||||||
input: 0
|
|
||||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
||||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
||||||
input_step: 10.0
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
M83
|
|
||||||
G1 E{menu.input} F240
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
### menu move 1mm ###
|
|
||||||
[menu __main __control __move_1mm]
|
|
||||||
type: list
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Move 1mm
|
|
||||||
|
|
||||||
[menu __main __control __move_1mm __axis_x]
|
|
||||||
type: input
|
|
||||||
name: Move X:{'%05.1f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.x}
|
|
||||||
input_min: {printer.toolhead.axis_minimum.x}
|
|
||||||
input_max: {printer.toolhead.axis_maximum.x}
|
|
||||||
input_step: 1.0
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G90
|
|
||||||
G1 X{menu.input}
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
[menu __main __control __move_1mm __axis_y]
|
|
||||||
type: input
|
|
||||||
name: Move Y:{'%05.1f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.y}
|
|
||||||
input_min: {printer.toolhead.axis_minimum.y}
|
|
||||||
input_max: {printer.toolhead.axis_maximum.y}
|
|
||||||
input_step: 1.0
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G90
|
|
||||||
G1 Y{menu.input}
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
[menu __main __control __move_1mm __axis_z]
|
|
||||||
type: input
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Move Z:{'%05.1f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.z}
|
|
||||||
input_min: 0
|
|
||||||
input_max: {printer.toolhead.axis_maximum.z}
|
|
||||||
input_step: 1.0
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G90
|
|
||||||
G1 Z{menu.input}
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
[menu __main __control __move_1mm __axis_e]
|
|
||||||
type: input
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Move E:{'%+06.1f' % menu.input}
|
|
||||||
input: 0
|
|
||||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
||||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
||||||
input_step: 1.0
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
M83
|
|
||||||
G1 E{menu.input} F240
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
### menu move 0.1mm ###
|
|
||||||
[menu __main __control __move_01mm]
|
|
||||||
type: list
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Move 0.1mm
|
|
||||||
|
|
||||||
[menu __main __control __move_01mm __axis_x]
|
|
||||||
type: input
|
|
||||||
name: Move X:{'%05.1f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.x}
|
|
||||||
input_min: {printer.toolhead.axis_minimum.x}
|
|
||||||
input_max: {printer.toolhead.axis_maximum.x}
|
|
||||||
input_step: 0.1
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G90
|
|
||||||
G1 X{menu.input}
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
[menu __main __control __move_01mm __axis_y]
|
|
||||||
type: input
|
|
||||||
name: Move Y:{'%05.1f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.y}
|
|
||||||
input_min: {printer.toolhead.axis_minimum.y}
|
|
||||||
input_max: {printer.toolhead.axis_maximum.y}
|
|
||||||
input_step: 0.1
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G90
|
|
||||||
G1 Y{menu.input}
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
[menu __main __control __move_01mm __axis_z]
|
|
||||||
type: input
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Move Z:{'%05.1f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.z}
|
|
||||||
input_min: 0
|
|
||||||
input_max: {printer.toolhead.axis_maximum.z}
|
|
||||||
input_step: 0.1
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G90
|
|
||||||
G1 Z{menu.input}
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
[menu __main __control __move_01mm __axis_e]
|
|
||||||
type: input
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Move E:{'%+06.1f' % menu.input}
|
|
||||||
input: 0
|
|
||||||
input_min: -{printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
||||||
input_max: {printer.configfile.config.extruder.max_extrude_only_distance|default(50)}
|
|
||||||
input_step: 0.1
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
M83
|
|
||||||
G1 E{menu.input} F240
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
|
|
||||||
### menu temperature ###
|
|
||||||
[menu __main __temp]
|
|
||||||
type: list
|
|
||||||
name: Temperature
|
|
||||||
|
|
||||||
[menu __main __temp __hotend0_target]
|
|
||||||
type: input
|
|
||||||
enable: {('extruder' in printer) and ('extruder' in printer.heaters.available_heaters)}
|
|
||||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
|
||||||
input: {printer.extruder.target}
|
|
||||||
input_min: 0
|
|
||||||
input_max: {printer.configfile.config.extruder.max_temp}
|
|
||||||
input_step: 1
|
|
||||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
|
||||||
|
|
||||||
[menu __main __temp __hotend1_target]
|
|
||||||
type: input
|
|
||||||
enable: {('extruder1' in printer) and ('extruder1' in printer.heaters.available_heaters)}
|
|
||||||
name: {"Ex1:%3.0f (%4.0f)" % (menu.input, printer.extruder1.temperature)}
|
|
||||||
input: {printer.extruder1.target}
|
|
||||||
input_min: 0
|
|
||||||
input_max: {printer.configfile.config.extruder1.max_temp}
|
|
||||||
input_step: 1
|
|
||||||
gcode: M104 T1 S{'%.0f' % menu.input}
|
|
||||||
|
|
||||||
[menu __main __temp __hotbed_target]
|
|
||||||
type: input
|
|
||||||
enable: {'heater_bed' in printer}
|
|
||||||
name: {"Bed:%3.0f (%4.0f)" % (menu.input, printer.heater_bed.temperature)}
|
|
||||||
input: {printer.heater_bed.target}
|
|
||||||
input_min: 0
|
|
||||||
input_max: {printer.configfile.config.heater_bed.max_temp}
|
|
||||||
input_step: 1
|
|
||||||
gcode: M140 S{'%.0f' % menu.input}
|
|
||||||
|
|
||||||
[menu __main __temp __preheat_pla]
|
|
||||||
type: list
|
|
||||||
name: Preheat PLA
|
|
||||||
|
|
||||||
[menu __main __temp __preheat_pla __all]
|
|
||||||
type: command
|
|
||||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
|
||||||
name: Preheat all
|
|
||||||
gcode:
|
|
||||||
M140 S60
|
|
||||||
M104 S200
|
|
||||||
|
|
||||||
[menu __main __temp __preheat_pla __hotend]
|
|
||||||
type: command
|
|
||||||
enable: {'extruder' in printer}
|
|
||||||
name: Preheat hotend
|
|
||||||
gcode: M104 S200
|
|
||||||
|
|
||||||
[menu __main __temp __preheat_pla __hotbed]
|
|
||||||
type: command
|
|
||||||
enable: {'heater_bed' in printer}
|
|
||||||
name: Preheat hotbed
|
|
||||||
gcode: M140 S60
|
|
||||||
|
|
||||||
[menu __main __temp __preheat_abs]
|
|
||||||
type: list
|
|
||||||
name: Preheat ABS
|
|
||||||
|
|
||||||
[menu __main __temp __preheat_abs __all]
|
|
||||||
type: command
|
|
||||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
|
||||||
name: Preheat all
|
|
||||||
gcode:
|
|
||||||
M140 S110
|
|
||||||
M104 S245
|
|
||||||
|
|
||||||
[menu __main __temp __preheat_abs __hotend]
|
|
||||||
type: command
|
|
||||||
enable: {'extruder' in printer}
|
|
||||||
name: Preheat hotend
|
|
||||||
gcode: M104 S245
|
|
||||||
|
|
||||||
[menu __main __temp __preheat_abs __hotbed]
|
|
||||||
type: command
|
|
||||||
enable: {'heater_bed' in printer}
|
|
||||||
name: Preheat hotbed
|
|
||||||
gcode: M140 S110
|
|
||||||
|
|
||||||
[menu __main __temp __cooldown]
|
|
||||||
type: list
|
|
||||||
name: Cooldown
|
|
||||||
|
|
||||||
[menu __main __temp __cooldown __all]
|
|
||||||
type: command
|
|
||||||
enable: {('extruder' in printer) and ('heater_bed' in printer)}
|
|
||||||
name: Cooldown all
|
|
||||||
gcode:
|
|
||||||
M104 S0
|
|
||||||
M140 S0
|
|
||||||
|
|
||||||
[menu __main __temp __cooldown __hotend]
|
|
||||||
type: command
|
|
||||||
enable: {'extruder' in printer}
|
|
||||||
name: Cooldown hotend
|
|
||||||
gcode: M104 S0
|
|
||||||
|
|
||||||
[menu __main __temp __cooldown __hotbed]
|
|
||||||
type: command
|
|
||||||
enable: {'heater_bed' in printer}
|
|
||||||
name: Cooldown hotbed
|
|
||||||
gcode: M140 S0
|
|
||||||
|
|
||||||
### menu filament ###
|
|
||||||
|
|
||||||
[menu __main __filament]
|
|
||||||
type: list
|
|
||||||
name: Filament
|
|
||||||
|
|
||||||
[menu __main __filament __hotend0_target]
|
|
||||||
type: input
|
|
||||||
enable: {'extruder' in printer}
|
|
||||||
name: {"Ex0:%3.0f (%4.0f)" % (menu.input, printer.extruder.temperature)}
|
|
||||||
input: {printer.extruder.target}
|
|
||||||
input_min: 0
|
|
||||||
input_max: {printer.configfile.config.extruder.max_temp}
|
|
||||||
input_step: 1
|
|
||||||
gcode: M104 T0 S{'%.0f' % menu.input}
|
|
||||||
|
|
||||||
[menu __main __filament __loadf]
|
|
||||||
type: command
|
|
||||||
name: Load Fil. fast
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__filament__load
|
|
||||||
M83
|
|
||||||
G1 E50 F960
|
|
||||||
RESTORE_GCODE_STATE NAME=__filament__load
|
|
||||||
|
|
||||||
[menu __main __filament __loads]
|
|
||||||
type: command
|
|
||||||
name: Load Fil. slow
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__filament__load
|
|
||||||
M83
|
|
||||||
G1 E50 F240
|
|
||||||
RESTORE_GCODE_STATE NAME=__filament__load
|
|
||||||
|
|
||||||
[menu __main __filament __unloadf]
|
|
||||||
type: command
|
|
||||||
name: Unload Fil.fast
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__filament__load
|
|
||||||
M83
|
|
||||||
G1 E-50 F960
|
|
||||||
RESTORE_GCODE_STATE NAME=__filament__load
|
|
||||||
|
|
||||||
[menu __main __filament __unloads]
|
|
||||||
type: command
|
|
||||||
name: Unload Fil.slow
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__filament__load
|
|
||||||
M83
|
|
||||||
G1 E-50 F240
|
|
||||||
RESTORE_GCODE_STATE NAME=__filament__load
|
|
||||||
|
|
||||||
[menu __main __filament __feed]
|
|
||||||
type: input
|
|
||||||
name: Feed: {'%.1f' % menu.input}
|
|
||||||
input: 5
|
|
||||||
input_step: 0.1
|
|
||||||
gcode:
|
|
||||||
SAVE_GCODE_STATE NAME=__filament__load
|
|
||||||
M83
|
|
||||||
G1 E{'%.1f' % menu.input} F60
|
|
||||||
RESTORE_GCODE_STATE NAME=__filament__load
|
|
||||||
|
|
||||||
### menu setup ###
|
|
||||||
[menu __main __setup]
|
|
||||||
type: list
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Setup
|
|
||||||
|
|
||||||
[menu __main __setup __save_config]
|
|
||||||
type: command
|
|
||||||
name: Save config
|
|
||||||
gcode: SAVE_CONFIG
|
|
||||||
|
|
||||||
[menu __main __setup __restart]
|
|
||||||
type: list
|
|
||||||
name: Restart
|
|
||||||
|
|
||||||
[menu __main __setup __restart __host_restart]
|
|
||||||
type: command
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Restart host
|
|
||||||
gcode: RESTART
|
|
||||||
|
|
||||||
[menu __main __setup __restart __firmware_restart]
|
|
||||||
type: command
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Restart FW
|
|
||||||
gcode: FIRMWARE_RESTART
|
|
||||||
|
|
||||||
[menu __main __setup __tuning]
|
|
||||||
type: list
|
|
||||||
name: PID tuning
|
|
||||||
|
|
||||||
[menu __main __setup __tuning __hotend_pid_tuning]
|
|
||||||
type: command
|
|
||||||
enable: {(not printer.idle_timeout.state == "Printing") and ('extruder' in printer)}
|
|
||||||
name: Tune Hotend PID
|
|
||||||
gcode: PID_CALIBRATE HEATER=extruder TARGET=210 WRITE_FILE=1
|
|
||||||
|
|
||||||
[menu __main __setup __tuning __hotbed_pid_tuning]
|
|
||||||
type: command
|
|
||||||
enable: {(not printer.idle_timeout.state == "Printing") and ('heater_bed' in printer)}
|
|
||||||
name: Tune Hotbed PID
|
|
||||||
gcode: PID_CALIBRATE HEATER=heater_bed TARGET=60 WRITE_FILE=1
|
|
||||||
|
|
||||||
[menu __main __setup __calib]
|
|
||||||
type: list
|
|
||||||
name: Calibration
|
|
||||||
|
|
||||||
[menu __main __setup __calib __delta_calib_auto]
|
|
||||||
type: command
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Delta cal. auto
|
|
||||||
gcode:
|
|
||||||
G28
|
|
||||||
DELTA_CALIBRATE
|
|
||||||
|
|
||||||
[menu __main __setup __calib __delta_calib_man]
|
|
||||||
type: list
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Delta cal. man
|
|
||||||
|
|
||||||
[menu __main __setup __calib __bedprobe]
|
|
||||||
type: command
|
|
||||||
enable: {not printer.idle_timeout.state == "Printing"}
|
|
||||||
name: Bed probe
|
|
||||||
gcode: PROBE
|
|
||||||
|
|
||||||
[menu __main __setup __calib __delta_calib_man __start]
|
|
||||||
type: command
|
|
||||||
name: Start probing
|
|
||||||
gcode:
|
|
||||||
G28
|
|
||||||
DELTA_CALIBRATE METHOD=manual
|
|
||||||
|
|
||||||
[menu __main __setup __calib __delta_calib_man __move_z]
|
|
||||||
type: input
|
|
||||||
name: Move Z: {'%03.2f' % menu.input}
|
|
||||||
input: {printer.gcode_move.gcode_position.z}
|
|
||||||
input_step: 1
|
|
||||||
realtime: True
|
|
||||||
gcode:
|
|
||||||
{%- if menu.event == 'change' -%}
|
|
||||||
G1 Z{'%.2f' % menu.input}
|
|
||||||
{%- elif menu.event == 'long_click' -%}
|
|
||||||
G1 Z{'%.2f' % menu.input}
|
|
||||||
SAVE_GCODE_STATE NAME=__move__axis
|
|
||||||
G91
|
|
||||||
G1 Z2
|
|
||||||
G1 Z-2
|
|
||||||
RESTORE_GCODE_STATE NAME=__move__axis
|
|
||||||
{%- endif -%}
|
|
||||||
|
|
||||||
[menu __main __setup __calib __delta_calib_man __test_z]
|
|
||||||
type: input
|
|
||||||
name: Test Z: {['++','+','+.01','+.05','+.1','+.5','-.5','-.1','-.05','-.01','-','--'][menu.input|int]}
|
|
||||||
input: 6
|
|
||||||
input_min: 0
|
|
||||||
input_max: 11
|
|
||||||
input_step: 1
|
|
||||||
gcode:
|
|
||||||
{%- if menu.event == 'long_click' -%}
|
|
||||||
TESTZ Z={['++','+','+.01','+.05','+.1','+.5','-.5','-.1','-.05','-.01','-','--'][menu.input|int]}
|
|
||||||
{%- endif -%}
|
|
||||||
|
|
||||||
[menu __main __setup __calib __delta_calib_man __accept]
|
|
||||||
type: command
|
|
||||||
name: Accept
|
|
||||||
gcode: ACCEPT
|
|
||||||
|
|
||||||
[menu __main __setup __calib __delta_calib_man __abort]
|
|
||||||
type: command
|
|
||||||
name: Abort
|
|
||||||
gcode: ABORT
|
|
||||||
|
|
||||||
[menu __main __setup __dump]
|
|
||||||
type: command
|
|
||||||
name: Dump parameters
|
|
||||||
gcode:
|
|
||||||
{% for name1 in printer %}
|
|
||||||
{% for name2 in printer[name1] %}
|
|
||||||
{ action_respond_info("printer['%s'].%s = %s"
|
|
||||||
% (name1, name2, printer[name1][name2])) }
|
|
||||||
{% else %}
|
|
||||||
{ action_respond_info("printer['%s'] = %s" % (name1, printer[name1])) }
|
|
||||||
{% endfor %}
|
|
||||||
{% endfor %}
|
|
||||||
Reference in New Issue
Block a user